Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
Make sure your extension cord is properly wired and in good electrical condition. Always replace a damaged extension cord or have it repaired by a qualified electrician before using it. Protect your extension cords from sharp objects, excessive heat, and damp or wet areas. RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS* (120 or 240 VOLT) NAMEPLATE AMPERES (at full load) EXTENSION CORD LENGTH 25 Feet 50 Feet 75 Feet 100 Feet 150 Feet 0 – 2.0 18 18 18 18 16 2.1 – 3.4 18 18 18 16 14 3.5 – 5.0 18 18 16 14 12 5.1 – 7.0 18 16 14 12 12 7.1 – 12.0 18 14 12 10 - 12.1 – 16.0 14 12 10 - - 16.1 – 20.0 12 10 - - - FIGURE C * Based on limiting the line voltage drop to five volts at 150% of the rated amperes. Symbology Double Insulated Canadian Standards Association Underwriters Laboratories, Inc. V~ Volts Alternating Current A Amperes n0 xxxx/min. No Load Revolutions per Minute (RPM) Unpacking When unpacking, check to make sure that all the parts are included. Refer to the Assembly Drawing and Parts List at the end of this manual. Not shown are five accessory Sanding Belts. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible. Assembly Instructions WARNING! Make sure the Power Switch of the Tool is in its Off (O) position and that the tool is unplugged from its electrical outlet before performing any assembly, inspection, maintenance, or cleaning procedures. Installing the Sanding Belt Remove Screw (26) and Cover (23). Refer to the photos on the next page. Turn the Slide Lock (36) completely to one side. This reduces the tension on the Roller (65) so that the Sanding Belt (66) can be slipped over easily. Place the Sanding Belt (66) over the Roller (65) and the Spindle (24). Turn the Slide Bar (36) so it points to the Pulley (65) and tightens the tension on the Sanding Belt (66). Replace Cover (23) and Screw (26). If needed, adjust the tracking of the Sanding Belt by turning the Adjustment Screw (59). Screw (26) Cover (23) Slide Lock (36) Roller (65) SandingBelt (66)Spindle (24) Operating Instructions Controls Switch (48) Brush Cover (41) Screw (49) Angle AdjustBracket (22) Slide Lock (36) Loosen Sanding BeltAdjusting Screw (59) Sanding Belt Tracking Operation 1. Secure the workpiece to be sanded. 2. Loosen Screw (49) and adjust Bracket (22) to the desired angle for sanding. 3. Plug the Line Cord (52) into a GFCI electrical outlet. 4. Always follow all safety instructions and warnings in this instruction manual. 5. Securely grasp the tool handle (with both hands) and press the On / Off Switch (48) to the On (I) position. 6. Begin sanding with light movements and pressure until the sanding capability is known on the material being sanded. 7. When finished using the Belt Sander, press the On / Off Switch (48) to the Off (O) position. Wait until the motor stops before setting the tool down. 8. Unplug the unit from the electrical outlet. INSPECTION, MAINTENANCE, AND CLEANING WARNING! Make sure the Power Switch of the Tool is in its Off (O) position and that the tool is unplugged from its electrical outlet before performing any inspection, maintenance, or cleaning procedures. 1. Before each use, inspect the general condition of the Belt Sander. Check for loose screws, misalignment , binding, or tears of sanding belt, cracked or broken parts, damaged electrical wiring, and any other condition that may affect its safe operation. If abnormal noise or vibration occurs, have the problem corrected before further use. Do not use damaged equipment. 2. Store in a clean and dry location. 3. Inspect the Carbon Brushes every few months for excessive wear; Sooner if the tool is used daily. Over time, if the performance of the tool diminishes, or it stops working completely, it may be necessary to replace the motor’s Carbon Brushes. The brushes are accessed by removing the Carbon Brush Cover (41) on top and bottom of the unit. Pull out the Carbon Brushes (40) and clean or replace both. This procedure should be completed by a qualified technician. 4. Before each use, inspect the general condition of the Belt Sander. Check for loose screws, misalignment or binding of moving parts, cracked or broken parts, damaged electrical wiring, and any other condition that may affect its safe operation. If abnormal noise or vibration occurs, have the problem corrected before further use. Do not use damaged equipment. 5. Clean the outside of the unit with a damp cloth. Never use solvents to clean any parts of this tool. Use compressed air to blow out debris from the motor vents. Parts List Part Description 1 Housing 2 Brush Holder 3 Stator 4 Brush Holder Ring 5 Screw, 4x65 6 Washer, Spring 7 Nut, M4 8 Nut Mount 9 Dust Seal 10 Armature 11 Bearing, 626 12 Cover, Inner 13 Bearing, 608 14 Bearing Cover A 15 Screw, M4x14 16 Washer, Spring 17 Woodruff Key 18 Washer, Flat 19 Washer, Spring 20 Nut, M6 21 Bear Box 22 Bracket 23 Cover 24 Spindle 25 Bearing, 608 26 Screw, M5x20 27 Gear ...