Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions please call 1-800-444-3353 SPECIFICATIONS ITEM DESCRIPTION Max. Air Pressure 90 PSI Air Speed 20,000 RPM Fitting Size 1/4” NPT Collet Sizes 1/4” 1/8” Accessories 11 mm Collet Wrench (Qty: 1) 17 mm Collet Wrench (Qty: 1) SAVE THIS MANUAL You will need this manual for the safety warnings and precautions, operating and maintenance procedures, parts lists and diagrams. Keep your invoice with this manual. Write the invoice number on the inside of the front cover. Keep this manual and invoice in a safe and dry place for future reference. SAFETY WARNINGS AND PRECAUTIONS 1. KEEP WORK AREA CLEAN AND DRY. Cluttered, damp or wet work areas invite injuries. 2. KEEP CHILDREN AWAY FROM WORK AREA. Do not allow children to handle the Air Angle Die Grinder. 3. STORE IDLE EQUIPMENT. When not in use, the Air Angle Die Grinder should be stored in a dry location to inhibit rust. Always lock up the Air Angle Die Grinder and keep out of reach of children. 4. DO NOT USE THE AIR TOOL KIT IF UNDER THE INFLUENCE OF ALCOHOL OR DRUGS. Read warning labels on prescriptions to determine if your judgement or reflexes are impaired while taking drugs. If there is any doubt, do not attempt to use this product. 5. USE EYE AND HEARING PROTECTION. Wear ANSI approved safety impact eye glasses and ANSI approved hearing protection when working with the Air Angle Die Grinder. ANSI approved safety impact eye glasses and hearing protection are available from Harbor Freight Tools. 6. DRESS SAFELY. Non-skid footwear or safety shoes should be used when working with this product. Do not wear loose clothing or jewelry as they can become caught in moving parts. Wear a protective hair covering to prevent long hair from becoming caught in moving parts. If wearing a long sleeve shirt, roll the sleeves up above the elbows. 7. DO NOT OVERREACH. Keep proper footing and balance at all times to prevent tripping, falling, back injury, etcetera. SKU 52848 PAGE 2 8. STAY ALERT. Watch what you are doing at all times. Use common sense. Do not use the Air Angle Die Grinder when you are tired or distracted from the job at hand. 9. CHECK FOR DAMAGED PARTS. Before using the Air Angle Die Grinder, carefully check that it will operate properly and perform its intended function. Check for damaged parts and any other conditions that may affect the operation of the Air Angle Die Grinder. Replace or repair damaged or worn parts immediately. 10. REPLACEMENT PARTS AND ACCESSORIES. When servicing, use only identical replacement parts. Only use tools and accessories intended for use with this Air Angle Die Grinder. Approved tools and accessories are available from Harbor Freight Tools. 11. MAINTAIN THESE PRODUCTS WITH CARE. Keep this tool and accessories clean and dry for better and safer performance. 12. MAINTENANCE: For your safety, service and maintenance should be performed regularly by a qualified technician. 13. USE THE RIGHT PRODUCTS FOR THE RIGHT JOB. There are certain applications for which this Air Angle Die Grinder was designed. Do not use a small tool or accessory to do the work of a larger industrial tool or accessory. Do not use this Air Angle Die Grinder for a purpose for which it was not intended. SPECIFIC PRODUCT WARNINGS AND PRECAUTIONS 1. USE CLEAN, DRY, REGULATED COMPRESSED AIR AT 90 PSI. Do not exceed the recommended 90 PSI. Never use oxygen, carbon dioxide, combustible gases or any other bottled gas as a power source for this tool. 2. DO NOT MODIFY THE SAFETY AIR SHUT-OFF SWITCH LOCATED ON THE THROTTLE LEVER (PART #2). The Air Angle Die Grinder features a Shut-Off Switch which, when pressure is released from the Throttle Lever, will automatically shut down the unit. For your safety and the safety of others, do not modify the Shut-Off Switch in any way. 3. WHEN CONNECTING TO THE AIR SUPPLY: A. If an automatic oiler is not used, add two drops of air tool oil into the air inlet of the Air Angle Die Grinder. (See Figure A.) B. Turn on the compressor and set the regulator to the recommended 90 PSI for this tool. 4. ALWAYS DISCONNECT TOOL FROM ITS AIR SUPPLY AND RELEASE ALL BUILT UP AIR PRESSURE BEFORE PERFORMING ANY SERVICES OR MAINTENANCE such as cleaning or changing accessories on the Air Angle Die Grinder, leaving the work area, moving the Air Angle Die Grinder from one location to another, handing the Air Angle Die Grinder to another person, etcetera. (See Figure A on page 4.) 5. WARNING! Some dust created by power sanding, sawing, grinding, drilling, and other construction activities, contain chemicals known (to the State of California) to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: lead from lead-based paints, crystalline silica from bricks and cement or other masonry products, arsenic and chromium from chemicall...