Take out collet (36) and grip housing (1) in a Vise fitted with soft jaws on the flats at the rear end and with a peg spanner or a punch unscrew clamp nut (33) - left hand thread - and grtp chuck spindle (34) and pull out the spindle assembly from the angle head housing (28). Support the underside of clamp nut (33) and tap the and of spindle (34) to drive the spindle through and to separate spindle (34), key (35), clamp nut (33). bearing {24) and bevel gear (30). If bearing (16) was 00» withdrawn when Sie sp«KSe assembly was pufed out, then tap the front iaca ot angle housirjg (28) so as to dislodge bearing (16). Do not remove Hush type grease fitting {31! Irom angle housing (28) unless a replacement is required. Drive out pin (13) and take off safety throttle lever (12). Unscrew housing cap (27) and remove with angle housing . Unscrew hose adaptor with screen (14) and take off O-riDg (15) from hose adaptor. !f a replacement is required, push out throttle valve bushing (£) with 2 Orings (3) and remove the 2 0-tjngs (3) from bushing ;2). Locate under the cylinder side (21) of rear end plate (17) and lap the rear end of rotor (18) to drive it through rear end plate (17) and bearing (16) assembly. With a suitable punch, tap out bearing (16) from rear end plate (17). Take off cylinder (21) noting for reassembly how it locates to rear end plate (17) and front end plate (23) by pin (20), Take out 4 rotor blades (19) from rotor (18). Grip rotor (18) very carefully so as not to damage or raise burrs on it and unscrew bevel gear Shat! (25) to release spindle collar (22) and ire»« end plate (23) with bearing (24). With a suitabie punch, tap oat bearing (24) from front end plate (23). Reassembly Clean and examine parts for wear and replace any parts only with those supplied by the manufacturer or authorized distributor. Ensure that Ihe faces of the end plates (17) and (23) that abut cylinder (21) are fiat and free from burrs and surface marking. If necessary, lap on a flat very fine grade of abrasive paper. Lightly coat an parts in suitable pneumatic tooi lubricating oil, pack bearings and gears with a lithium or jnoiybdenuro based general purpose grease and assesrifeie in Sis reverse order. NOTE; when reassembling the angle head assembly.» the tool the running clearance between gears (30) and (25) can be achieved by adjustment of angle housing (28) and housing cap (27). With the lever (12) depressed, pour into hose adaptor (14) Sml of a suitable pneumatic tool lubricating oil and release lever and oonnect to a suitable air supply and operate tool slowly for a few seconds to allow the oil to circulate. Check the function of the collet, safety lever and air regulator before returning to service. Before fitting mounted point grinding wheal, check ihe speed of She tool and ihe point - refer to section “Operating“. Operation Specification j Air Consumption 4.0 cfm (28 scfm) j Horse Power 0.2(150 Watts) Air Inlet Thread 1/4-18NPT Overaii Length 5.5“ (140 mm) j M 90 PSÍG/&2 bar j Declaration of Conformity C€ Sioux Tools Inc. 117 Levi Drive, Murphy, NO 28906, U.S.A. declare under our sole responsibility that the product Model 5055A/5055AM6 Mini Die Grinders (R/Ä Head), Serial Number to which this declaration relates is in conformity »rife the toll owing standard(s) of other normative documents) EN792 (Draft), EN292 Parts 1 & 2, ISO 8662 Parts 1 & 17, Pneurop PN8NTC1 following the provisions of 89/392/EEC as amended by 91/368/EEC & 93/44/EEC Directives GeMaE. Seebeck (President) Name and sly «gut» or eqiiteaiam mariang of auttwiwj person Prôied in Taiwan Page No 3 Modèle 5055A/5055AM6 Mini-meuleuse - tête à angle droit Instructions de fonctionnement Comprend : Utilisation prévue, stations de travail, mise en service, fonctionnement, démontage, montage et règles de sécurité. Important Lisez attentivement ces instructions avant d'installer, de faire fonctionner, d'entretenir ou de réparer cet outil. Gardez ces instructions dans un endroit sûr et facilement accessible. Fabricant/Fournisseur Sioux Tools, Inc. 117 Levi Drive Murphy, NC 28906 U.S.A. Tel No. 828-835-9765 Type de produit Mini-meuleuse • tête à angle droit Fax No. 828-835-9685 Numéro du modèle 5055A-1/4" 5055AM6 - 6 mm Tours par minutes 20.000 tfmin C€ Numéro de série Poids net du produit 0,50 kg Emploi conseillé d’un dispositif d’équilibrage ou d’un support. NON Alésage de tuyau recommandé Taille minimum 8 mm Longueur maximum de tuyau recommandée 10 m Pression d’air De fonctionnement recommandée Max...
)
