Оценок - 4, средний балл: 4 ( )

Производитель: MRV Communications Размер: 3.19 mb Название файла: Язык инструкции:

4.All the buttons except the sleeping button is no effective after wire controller received lock signal fromremote controller. 6 functions fo non-negative ion unit. 8 12 17 19 20 24 25 26 30 3 23 D Remote LCD display contents and key name and each key function introduction TEMP HEALTH FAN MODE SWING TIMER ON OFF LOCKRESETCODE OFF H AUTO ion 6 4 2 7 8 9 10 12 13 14 15 16 17 18 19 11 20 21 B A 1.ON/OFF button Used to turn on/off unit 2.Temperature Setting button Used to set temperature, temperature range: 16 C~30 C 3.Health Used to control the generating oxygen function and negative ion-function 4.Operation mode button Used to set working mode: Cooling, Dehumidifying, Heating 5.Timer button Used to set the mode of timer 6.Reset button When the remote controller appears abnormal condition, use a sharp-pointed article to press this button to make the wire controller resume normal 7.Fan speed button Used to set fan speed 8.Swing button Used to set Auto Swing or Fixed air sending direction 9.Time Adjusting button 10.Lock button Press on time lock all the key sand press another timeconcel the lock. 11.Working mode display 12.Fan speed display Used to display the fanspeed. After setting"AUTO" function,air speedcan auto change accordingto the temp. differencebetween the room temp. andsetting temp. 13.Health running display Used to display healthy running. 14.Timer ON/OFF display Display Timing mode. "Blank" No Timing " OFF ON " Timing off " " Timing on 15.Signal display Sending out signal to the remote receiver. 16.Temperature display Display the setting temp. value. 17.Lock display Display the key have been locked. 18.Super/Soft operation display 19.Timing time display Display timing open time or timing close time 20.Signal launch head Use to send signal to the indoor unit receive window. 21.Code Select remote control receive code(H-MRV Remote cnotroltype use A code) Make sure that the remote controller is used within 7 meters from receiver window of the wire controller and there are no obstructions in between. The remote controller or wire controller should be handled with care. When operating the remote controller in an area where electronically controlled lights are installed or wireless handsets are used, move closer to the indoor unit as the function of the remote controller might be affected by signals from this equipment. Note: 1.After change the battery, working condition resume as follows: Working mode:cooling 18Timming mode: normal Air speed: Auto 2.The units used in this manual no 8 functions. The health key can only control the negative generator. R Temp. 26 C 7 D D Clock set When unit is started for the first time, clock should be adjusted as follows: Press CLOCK button, "AM"or "PM" flashes. Press or to set correct time. Each press will increase or decrease 1min. If the button is kept depressed, time will change quickly. After time setting is confirmed, press SET, "AM "and "PM" stop flashing, while clock starts working. Battery loading Batteries are fitted as follows: Remove the battery compartment lid Slightly press and disengage the battery compartment lid marked with i * ** * i and then hold the remote controller by the upper section and then remove the battery compartment lid by pressing in the direction of the arrow as shown in the figure above. Loading the battery Ensure that batteries are correctly placed in the compartment as required for positive and negative terminals. Replacing the battery compartment lid The battery compartment lid is reinstalled in the reverse sequence. Display review Press the button to see if batteries are properly fitted. If no display appears, refit the batteries. Caution: If the remote controller does not operate as designed after fitting new batteries of the same type, press the Reset button (marked ) with a pointed article. Note: It is recommended that the batteries be removed from the compartment if the remote controller is not used for an extended period. The remote controller is programmed for automatic test of operation mode after the batteries are replaced. When the test is conducted, all icons will appear on the screen and then disappear if the batteries are properly fitted. When the display become weak, this display no power in the battery, please change the battery. R 1 3 4 5 2 1 .Emergency switch2 .Power lamp After open the unit, this lamp bright when theunite enter health running, the lamp change fromorange to blue lamp. 3 .Timing lamp When the unit been setting Timing running, thislamp bright. 4 .Running lamp When the compressor working, this lamp bright. 5 .Indoor temp. sensorTest the room temperature. 8 Important Points of Safety The following four important points of safety and suggestions should be paid great attention: Warning: Misuse may cause fatal result such as death or serious injury etc. Attention: Misuse may cause human injury or damage of machine, in some case fatal results. : Content marked with this iforbiddeni sign should be absolutely for...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: