Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
Assembly and Operation Instructions Made in China For technical questions and replacement parts, please call 1-800-222-5381. Thank you very much for choosing a NORTHERN TOOL + EQUIPMENT CO., Product! For future reference, please complete the owner's record below: Model: _______________ Purchase Date: _______________ This product is designed for certain applications only. Northern Tool + Equipment strongly recommends that this product is not modified and/or used for any application other than that for which it was designed. If you have any questions relative to a particular application, DO NOT use the product until you have first contacted Northern Tool + Equipment to determine if it can or should be performed on the product. Before using this product, please read the following instructions carefully. SPECIFICATIONS Save the receipt, warranty and these instructions.It is important you read the entire manual to become familiar with this product before you begin using it. Electrical Requirements Power Input: 110V AC / 60Hz Power Cord Length: 70-7/8" (180cm) Power Cord Plug Type: 3-Prong, Grounded Speed Variable speed 0 ~ 10,000 RPM Grinding Wheel 3" Diameter x 3/4" Thick Buffing Wheel 3" Diameter x 3/4" Thick Arbor Size 1/2" (12mm) Diameter SAVE THIS MANUAL You will need this manual for the safety warnings, operating and maintenance procedures, parts list and diagram. Keep your invoice with this manual. Write the invoice number on the inside of the front cover. Keep the manual and invoice in a safe and dry place for future reference. Safety Warnings and Precautions WARNING: When using this tool, basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment. Read all instructions before using this product. 1. Avoid working alone. Should an accident occur, an assistant can bring help. 2. Disconnect power. Unplug tool when not in use, before servicing and when changing accessories such as grinding wheels. Never walk away and leave the tool running. 3. Keep work area clean. Cluttered areas invite injuries. 4. Keep children and pets away. Children must never be allowed in the work area. Do not let them handle machines, tools, or extension cords. Never allow unsupervised or untrained personnel to operate the machine. 5. Store idle equipment. When not in use, tool must be stored in a dry location to inhibit rust. Always lock up tools and keep out of reach of children. 6. Dress properly. Do not wear loose clothing or jewelry as they can be caught in moving parts. Protective electrically nonconductive clothes and nonskid footwear are recommended when working. Wear restrictive hair covering to contain long hair. Wear an ANSI-approved dust mask or respirator. 7. Use eye protection. Always wear ANSI-approved impact-resistant safety goggles. 8. Do not overreach. Keep proper footing and balance at all times. Do not reach over or across electrical cables or frames. 9. Maintain tools with care.Inspect grinding wheels and power cord periodically for cracks and other damage. if necessary, have them repaired by an authorized technician. 10. Use the right tool for the job. Do not attempt to force a small tool or attachment to do the work of a larger industrial tool. There are certain applications for which this tool was designed. Do not modify this tool and do not use this tool for a purpose for which it was not intended. 11. Stay alert. Watch what you are doing and use common sense. Do not operate any tool when you are tired or under the influence of alcohol or drugs. Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not operate the tool. ! 1 of 5 12. Check for damaged parts. Before using this tool, any part that appears damaged should be carefully checked to determine that it will operate properly and perform as intended. Check for alignment and binding of moving parts, broken parts or mounting fixtures and any other conditions that may affect proper operation. Any part that is damaged should be properly repaired or replaced by a qualified technician. Do not use the tool if any switch does not turn on and off properly. 13. Replacement parts and accessories.When servicing use only identical replacement parts. Use of other parts will void the warranty. Only use accessories intended for use with this tool. 14. Use proper size and type extension cord. If an extension cord is required. It must be of the proper size and type to supply the correct current to the tool without heating up; otherwise, the extension cord could melt and catch fire or cause electrical damaged to the tool. This tool requires use of an extension cord of 0 to 10 Amps capability (up to 50 feet), with wire size rated at 18 AWG. Longer extension cords require a larger size wire. If you are using the tool outdoors, use an extension cord rated for outdoor use (signified by "WA" on the jacket). 15. Take caution as some woods conta...