Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
Keep proper footing and balance at all times. 14. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories. 15. USE RECOMMENDED ACCESSORIES. Consult the owner’s manual for recommended accessories. The use of improper accessories may cause risk of injury. 16. REDUCE THE RISK OF UNINTENTIONAL STARTING. On machines with magnetic contact starting switches there is a risk of starting if the machine is bumped or jarred. Always disconnect from power source before adjusting or servicing. Make sure switch is in OFF position before reconnecting. 17. MANY WOODWORKING TOOLS CAN “KICKBACK” THE WORKPIECE toward the operator if not handled properly. Know what conditions can create “kickback” and know how to avoid them. Read the manual accompanying the machine thoroughly. 18. CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced. 19. NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF. Do not leave tool until it comes to a complete stop. 20. NEVER OPERATE A MACHINE WHEN TIRED, OR UNDER THE INFLUENCE OF DRUGS OR ALCOHOL. Full mental alertness is required at all times when running a machine. 21. NEVER ALLOW UNSUPERVISED OR UNTRAINED PERSONNEL TO OPERATE THE MACHINE. Make sure any instructions you give in regards to machine operation are approved, correct, safe, and clearly understood. 22. IF AT ANY TIME YOU ARE EXPERIENCING DIFFICULTIES performing the intended operation, stop using the machine! Then contact our service department or ask a qualified expert how the operation should be performed. H4380 Buffer -3 Additional Safety Instructions For Buffers 1. ALWAYS WEAR EYE PROTECTION! 2. WEAR AN APPROVED DUST MASK OR RESPIRATOR. Buffing operations produce dust. 3. MAKE SURE BUFFER IS SECURED FIRMLY TO A BENCH OR STAND BEFORE USE. Any “wobbles” must be corrected by shimming or blocking before operation. 4. DO NOT USE GRINDING WHEELS ON THIS MACHINE. It is strictly designed for buffing and drum sanding only. 5. DO NOT stand directly in front of buffing or sanding accessories when turning machine on. 6. PERFORM machine inspections and maintenance service promptly when called for. To operate this or any power tool safely and efficiently, it is essential to become as familiar with it as possible. The time you invest before you begin to use your Model H4380 will be time well spent. DO NOT operate this machine until you are completely familiar with the contents of this manual or serious personal injury may occur. 7. DO NOT allow your hands to come into contact with buffing wheels during operation. Abrasive accessories have the ability to remove a lot of material, including skin, very quickly. 8. ANY PROBLEM concerned with any moving parts or accessories must be investigated and corrected with the power disconnected, and after everything has come to a complete stop. 9. NEVER leave the machine running unattended. 10. NEVER BUFF BY PLACING THE WORKPIECE ON TOP OF THE BUFFING WHEEL. The wheel may kick the workpiece toward the operator. Always buff on the downward part of the buffing wheel. 11. HOLD THE WORKPIECE FIRMLY WHILE BUFFING. No list of safety guidelines can be complete. Every shop environment is different. Always consider safety first, as it applies to your individual working conditions. Use this and other machinery with caution and respect. Failure to follow guidelines could result in serious personal injury, damage to equipment or poor work results. -4- H4380 Buffer SECTION 2: CIRCUIT REQUIREMENTS 110V Operation The Model H4380 is wired for 110V. The 1.2 H.P. motor will safely draw 3.5 amps at 110V. If you operate this machine on any circuit that is already close to its capacity, it might blow a fuse or trip a circuit breaker. However, if an unusual load does not exist and a power failure still occurs, contact a qualified electrician or our service department. A 10 amp circuit should be used with this buffer. Always check to see if your current wires are capable of handling a 10 amp load. If you are unsure, consult the advice of a qualified electrician. Extension Cords If you find it necessary to use an extension cord with the Model H4380, make sure the cord is rated Hard Service (grade S) or better. Refer to the chart in the standard safety instructions to determine the minimum gauge for the extension cord. The extension cord must also contain a ground wire and plug pin. Always repair or replace extension cords when they become worn or damaged. Grounding In the event of an electrical short, grounding reduces the risk of electric shock by providing electric current a path of lea...