Оценок - 5, средний балл: 4
(
)
)
|
Фрагмент инструкции
When vacuuming dry dust that is especially detrimental to health or carcinogenic, use a vacuum cleaner that is specifically intended for that purpose. BOSCH VACUUM HOSE DM 2610958399 10-10:DM 2610958399 10-10 i:55 AM Page 10 Introduction INTENDED USE This Bosch Multi-X Oscillating Tool is intended for dry sanding of surfaces, corners, edges, for scraping, for sawing soft metals, wood and plastic components, and for grout removal using the applicable tools and accessories recommended by Bosch. Operating Instructions LEARNING TO USE THE TOOL Getting the most out of your oscillating tool is a matter of learning how to let the speed and the feel of the tool in your hands work for you. The first step in learning to use the tool is to get the “feel” of it. Hold it in your hand and feel its weight and balance (Fig. 4). Depending on the application, you will need to adjust your hand position to achieve optimum comfort and control. The unique comfort grip on the body of the tool allows for added comfort and control during use. When holding tool, do not cover the air vents with your hand. Blocking the air vents could cause the motor to overheat. IMPORTANT! Practice on scrap material first to see how the tool’s high-speed action performs. Keep in mind that your tool will perform best by allowing the speed, along with the correct accessory, do the work for you. Be careful not to apply too much pressure. Instead, lower the oscillating accessory lightly to the work surface and allow it to touch the point at which you want to begin. Concentrate on guiding the tool over the work using very little pressure from your hand. Allow the accessory to do the work. Usually it is better to make a series of passes with the tool rather than to do the entire job with one pass. To make a cut, for example, pass the tool back and forth over the work. Cut a little material on each pass until you reach the desired depth. SLIDE "ON/OFF' SWITCH The tool is switched "ON" by the slide switch located on the topside of the motor housing (Fig. 1). TO TURN THE TOOL "ON" slide the switch button forward to the “I” . TO TURN THE TOOL "OFF" slide the switch button backward the “0” . ELECTRONIC FEEDBACK Your tool is equipped with an internal electronic feedback system that provides a “soft start”, which will reduce the stresses that occur from a high torque start. The system also helps to keep the preselected speed virtually constant between no-load and load conditions. VARIABLE SPEED DIAL This tool is equipped with a variable speed dial. The speed may be controlled during operation by presetting the dial in any one of six positions (Fig. 1). OPERATING SPEEDS The Bosch Multi-X has a high oscillating motion of 8,000 - 20,000 /min (OPM). The high speed motion allows the Bosch Multi-X to achieve with excellent results. The oscillating motion allows the dust to fall to the surface rather than slinging particles into the air. To achieve the best results when working with different materials, set the variable speed control to suit the job (See Speed Chart on Page 12 for guidance) . To select the right speed for the accessory in use, practice with scrap material first. -10- DM 2610958399 10-10:DM 2610958399 10-10 i:55 AM Page 11 NOTE: Speed is affected by voltages changes. A reduced incoming voltage will slow the OPM of the tool, especially at the lowest setting. If your tool appears to be running slowly, increase the speed setting accordingly. The tool may not start at the lowest switch setting in areas where outlet voltage is less than 120 volts. Simply move the speed setting to a higher position to begin operation. The variable speed control settings are marked on the speed control dial. The settings for approximate /min (OPM) are: Switch Setting Speed Range /min (OPM) 8,000 10,400 12,800 15,200 17,600 20,000 You can refer to the charts on next page to determine the proper speed, based on the material and accessory being used. These charts enable you to select both the correct accessory and the optimum speed at a glance. 1 2 -11- -zv Multi-X Accessory Speed Settings * Soft steel only DM 2610958399 10-10:DM 2610958399 10-10 10/5/W 10:56 AM Page 13 Operating Applications APPLICATIONS Your Bosch Multi-X oscillating tool is intended for sanding and cutting wooden materials, plastic, plaster and non-ferrous metals. It is especially suitable for working close to edges, in tight spaces, and for flush cutting. Below are some typical uses for your Bosch Multi-X oscillating tool. A WARNING For all accessories, work with the accessory away from the body. Never position hand near or directly in front of working area. Always hold the tool with both hands and wear protective gloves. Flush Cutting Remove excess wood from door jamb, window sill and/or toekick. Removing excess copper or PVC pipe. Removal work e.g. carpets & backing, old tile adhesives, caulking on masonry, wood and other surfaces. Removal of excess...