Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
Date/ Time SettingYou can change time setting from this page. Clicks “Apply” to save the setting. By default SNTP is set to Network Time Service otherwise select synchronize to PC. If internet access is available, we recommended setting SNTP to Network Time Service instead. IP Configuration By default, “IP Config” is set to “Automatic IP”. This will allow the NAS adapter to obtain its IP address automatically. If you prefer setting it manually, select the static IP option, enter your own value and click “Apply” to confirm the new setting. Disk Utility In this page, you can manage hard disk settings of the USB storage device. Format: For first time installation, you need to format hard disk into FAT32 file system. Formatting the drive will erase all data on the hard drive. Warning: For hard drives with data on it, be fore you have a backup before proceeding to format the hard drive! Tip: You can transfer back the backup data to the NAS Public folder for sharing via the network or USB connection of the USB Storage device. Sleep Time: This is to select hard disk sleeping mode. Scan Disk: After the scan, it will show file content information and health status for the hard disk. Maintenance This page allows you to update the NAS adapter firmware, to go back to factory default settings or reboot NAS system. Firmware update: Follow the steps below to update the loader and firmware for NAS adapter. 1. Download the latest firmware. 2. Store the firmware file on your computer and decompress them if necessary. 3. Browse your system and locate the firmware (BIN file). 4. Click on “Upload”. 5. Confirm the pop-up massage to start the update. 6. Wait and DO NOT click anywhere else or turn off the power. The upgrade might take a few minutes. 7. Once the update is done, it will prompt you to reboot the device. 8. Click on ”reboot” to restart the device. 9. Wait for about one minute and then go to the status page to confirm the update was successful. Factory defaults: If you experience problems after a firmware update, it is recommended to reset all settings. Note: Resetting the device will remove all folder from the sharing list, erase the FTP accounts, and reset all other settings! Please do not power off or disconnect NAS adapter connection during the firmware update process. System reboot: This can be used to restart the network drive after a firmware update. Click “Modify” to share a folder. Select “User1” from Folder List and click the “a” to add user on “Sharing List”. SMB Server SMB server allows you to share data or files through the network LAN. When a USB storage device is connected, a default Public folder is available to be shared among Guest users. A default Guest user is also created. Note: Only use English alphabet for folder names and no special characters when creating new folders. How to create a user Click on the “Add” button and type new account name and password. Click “OK”. The NAS adapter will also create a SAMBA folder named “User1”. To Access the folder From the Windows start button, type “Run”, and type \\ follow by the IP address. Eg:\\192.168.1.121 and click OK to continue. Type “User1” and password to login. Enter new password then click “Apply” to save setting. How to delete a SAMBA account Now you have set up the folder that you wish to share on your NAS adapter. This Select an account you wish to delete. Click “Delete” to proceed. Pleasefolder can be access from other computer on your local network. note that all the data inside the folder will be lost after the delete. How to modify account password Select “User1” and then click “Modify”. FTP Server Remember to “Enable” the FTP service on the status page, when you plan on using the FTP server. FTP server Configuration: The standard port for FTP service is 21. If required, you can change it from any port between 1025-65500. But in general, we recommended using the default port of 21. File language support: By default, the encoding is set to English. If you want to store or transfer files with a different encoding (different language), choose the corresponding language for the drop down list. In order to transfer and view the files correctly, it is important that you select the correct language! Anonymous: By default an anonymous user name has been created, it allows FTP users to login without username and password. For security reasons, it is best to add a password! Note: To be able share FTP resource you need a router to assign the IP address. How to create FTP account FTP allows you to share your data through the internet. An internet connection is required before setting up FTP server. Select FTP server and click the “Add” button. Enter a name and password for the new FTP account and click “Next” to continue. In the account list, you can see an overview of the existing accounts and status. Click “Apply”. For FTP file transfers, we recommend to use other dedicated FTP client software e.g.: SyncQuick FTP, Cute FTP etc. Note: When creating FT...
Эта инструкция также подходит к моделям:Сетевое оборудование - NASU2 (4.73 mb)
Сетевое оборудование - NASU2 (4.73 mb)