Оценок - 0, средний балл: 0
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
Your unit’s color might vary from the color shown in this manual. 12367458 Figure 4. ReadyNAS Ultra 4, Ultra 4 Plus, Pro 4, NVX Pioneer, and NVX (Business Edition) front and side panels 1. Exhaust vents 2. USB 2.0 port 3. Backup button and backup LED 4. Disk LEDs 5. Disk activity LED 6. Power button and LED 7. Drive bay door 8. Status display screen Drive Bay This section describes the drive bay of ReadyNAS Ultra 4, Ultra 4 Plus, Pro 4, NVX Pioneer, and NVX (Business Edition) units. 36143254 Figure 5. ReadyNAS Ultra 4, Ultra 4 Plus, Pro 4, NVX Pioneer, and NVX (Business Edition) drive bay 1. Drive bay door 2. Disk bays 3. Recessed disk tray locking mechanism 4. Disk release latch 5. Disk tray latch handle 6. Disk tray Rear Panel This section describes the rear panel of ReadyNAS Ultra 4, Ultra 4 Plus, Pro 4, NVX Pioneer, and NVX (Business Edition) units. 125643 Figure 6. ReadyNAS Ultra 4, Ultra 4 Plus, Pro 4, NVX Pioneer, and NVX (Business Edition) rear panel 1. Exhaust fan 2. Power cable socket 3. Reset button 4. LAN1 and LAN2 gigabit Ethernet ports with LED status indicators 5. USB 2.0 ports 6. Kensington lock Status Information You can obtain information about the status of your unit by reviewing the indicators listed in the following table. Item Description Power button and LED Press this button to turn on the ReadyNAS. The LED has these states: • Blinking. Booting • Blue. Powered on • Off. Powered off Disk LEDs (1, 2, 3, 4) Each disk bay has an LED associated with it, in numerical order from left to right, along the top of the front panel of the unit. The disk LEDs have these states: • On. Power is on and the disk is operating normally. • Blinking. The disk failed or is resynchronizing. See the status display screen for details. • Off. The disk bay is empty. Disk activity LED The disk activity LED has these states: • Blinking green. A disk is active. • Off. No disks are active. Rear panel Ethernet port LEDs Two LED status indicators are built into these ports. One LED indicates port activity. The other LED indicates connection speed as follows: • Green. The port is operating at 1,000 Mbps. • Amber. The port is operating at 100 Mbps. • Off. The port is operating at 10 Mbps. Status display screen Displays messages about the status of your unit. Note that the status display screen goes to sleep to prevent burn-in; to wake it, press the Power button. If the unit reports an abnormal operation or error, the status display screen stays on. System Shutdown You can shut down your unit in two ways: • Using the Power button: • Preferred shutdown: • If the status display screen is not lit, press the Power button three times to initiate a graceful shutdown. • If the status display screen is lit, press the Power button two times to initiate a graceful shutdown. • Forced shutdown. If the unit is hung, press the Power button and hold for 5 seconds to force shutdown. • Using FrontView. For information about using FrontView to shut down your storage system, see the software manual for your unit, which is available at Boot Menu Use the boot menu to restart or troubleshoot your ReadyNAS unit. Your unit has the following boot modes: • Normal. Initiates a normal boot process, just like booting using the Power button. • Factory default. Initiates a short disk test that takes approximately 5 minutes, then begins a 10-minute time-out period waiting for RAIDar. During the 10-minute time-out period, the system can be powered off safely without causing any data loss. After 10 minutes, or if you select the factory default option with RAIDar during the time-out period, the factory default process begins. The factory default reboot process resets the unit to factory settings, erases all data, resets all defaults, and reformats the disk to X-RAID2. • OS reinstall. Reinstalls the firmware from the internal flash to the disks. Use the OS reinstall boot mode when the system crashes and corrupts some configuration files. OS reinstall boot mode also resets some settings on your unit, such as I...
Эта инструкция также подходит к моделям:Сетевое оборудование - RNDX400E (ReadyNAS NVX Pioneer) (1.32 mb)
Устройства обработки данных - RNDP200U (ReadyNAS Ultra 2 Plus) (1.32 mb)
Устройства обработки данных - RNDP400U (ReadyNAS Ultra 4 Plus) (1.32 mb)
Устройства обработки данных - RNDP600U (ReadyNAS Ultra 6 Plus) (1.32 mb)