Оценок - 0, средний балл: 0
(
)
)
|
К этому устройству также есть другие инструкции:
Сетевое оборудование - R6200 (3.03 mb)
Сетевое оборудование - R6200 (1.24 mb)
Фрагмент инструкции
350 East Plumeria Drive San Jose, CA 95134, USA December 2012 Technical Support Thank you for selecting NETGEAR products. After installing your device, locate the serial number on the label of your product and use it to register your product at Registration is required before you can use NETGEAR telephone support service. NETGEAR recommends registering your product through the NETGEAR website. Visit for product updates and web support. NETGEAR recommends that you use only the official NETGEAR support resources. Dual Band 11ac WiFi Router R6200 Installation Guide Package Contents The box should contain the following items. If any items are incorrect, missing, or damaged, contact your NETGEAR dealer. Note: In some regions, a resource CD is included with your product. Important: Be sure to remove the plastic film from the router before using it. Ethernet cable Dual Band WiFi Router Power adapter You can use this diagram to connect your router or follow the detailed instructions in this booklet. 1. Prepare your modem. the router. 5. Launch a browser. 2. Connect your modem. Unplug your modem. If it has a battery backup, remove the battery. Plug in your modem. Put the battery back in. Then cable the modem to the router Internet port. Modem Internet Router DSL or cable 4. Connect 3. Power on a computer. User Manual You can get the user manual online at or through a link in the products’s user interface. Declarations of Conformity For complete EU Declarations of Conformity, visit © NETGEAR, Inc. All rights reserved. Intended for indoor use only in all EU member states, EFTA states, and Switzerland 1 Contents Install Your Router 2 Prepare your modem. 2 Connect your modem. 2 Power on the router. 3 Connect a computer. 3 Launch a browser. 4 Preset Wireless Security 4 Wireless Network Settings 5 Add Wireless Devices to the Network 6 WPS Method 6 Manual Method 6 Access the Router to Make More Changes 7 Troubleshooting 9 ReadySHARE Access 9 Other Features 10 2 Install Your Router Make sure that your Internet service is active before you install the router. Follow steps 1 through 5. 1. Prepare your modem. a. Unplug your modem’s power. b. If the modem has a battery backup, remove its batteries. c. If your modem was already connected to another router, disconnect the cable between your modem and that router. Your modem should now be completely turned off, and cabled only to the wall jack for your Internet service. 2. Connect your modem. a. Plug in, then turn on your modem. (Replace the batteries if you removed them previously.) b. With the yellow Ethernet cable that came with the router, connect your modem to the Internet port of your router. 1 Internet DSL or cable Modem 2 a b Router Modem 3 3. Power on the router. a. Connect the power adapter to the router and plug the power adapter into an outlet. b. Before going to Step 4, wait for the Wireless LED on the front panel of the router to light. If none of the LEDs on the front panel are lit, press the Power On/Off button on the rear panel of the router. 4. Connect a computer. You can use an Ethernet cable (not included) or connect wirelessly. • Use the Ethernet cable to connect your computer to an Ethernet port on your router. • Or connect wirelessly by using the preset wireless security settings shown on the product label. 3 a b On/Off Router Modem 4 Router Modem Computer 4 5. Launch a browser. If a web page does not open, close and reopen the browser and type in the address bar, or see Troubleshooting on page 9. Preset Wireless Security This product has a unique WiFi network name (SSID) and network key (password). The default SSID and password are uniquely generated for every device, like a serial number, to protect and maximize your wireless security. This information is on the product label. NETGEAR recommends that you do not change the preset SSID or password. If you do change the settings, the security SSID and password on the bottom of the product no longer apply. 5 5 Wireless Network Settings Record the default preset wireless settings that are printed on the label here for easy reference. If you change the default settings, record them here for easy reference, and then store this booklet in a safe place: To retrieve or update your wireless password, type in a web browser and log in using the default user name (admin) and password (password). Select Wireless Settings to locate your wireless password. WiFi network name (SSID): Network key (password): WiFi network name (SSID): Network key (password): 6 Add Wireless Devices to the Network Choose either the manual or Wi-Fi Protected Setup (WPS) method to add wireless computers and other devices to your wireless network. WPS Method If your wireless device supports WPS—NETGEAR calls this method Push 'N' Connect—you might be prompt...