Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
You can also consult the Reference Manual on the NETGEAR, Inc. Web site at The WGE111 Wireless Game Adapter operates in either Infrastructure or Ad-Hoc mode. If you would like to change the default IP address or access the wireless game adapter Web configuration console, see the “Smart Wizard Configuration Assistant” section on this card. The default IP address is 192.168.0.202. Internet Game Console Plug-and-Go What you need • Broadband Internet access through a router with an 802.11b or 802.11g wireless access point (built in to the router or separate) without any security features enabled. Note: If you enabled security features (like WEP, WPA-PSK, SSID broadcast off, MAC filtering, etc.) you need to follow the instructions in the Reference Manual. • A network-enabled game console. What you do 1. 2. Make sure that the switch on the back of the WGE111 is set to the left side (labeled Internet), which corresponds to Infrastructure Mode. 3. Connect the power adapter to the WGE111 and verify the following: • The power light goes on. • The Internet light is lit. • The Ethernet light is lit when connected to a powered on network- enabled game console. 4. Enjoy your Internet gaming! Personal Computer Plug-and-Go What you need • Broadband Internet access through a router with an 802.11b or 802.11g wireless access point (built in to the router or separate) without any security features enabled. • A computer to run the initial configuration. What you do 1. Connect the Ethernet cable from your WGE111 Wireless Game Adapter (A) to the Ethernet port on your computer (B). 2. Make sure that the switch on the back of the WGE111 is set to the left side (labeled Internet), which corresponds to Infrastructure Mode. 3. Connect the power adapter to the WGE111 and verify the following: • The power light goes on. • The Internet light is lit. • The Ethernet light is lit. 4. Enjoy your Internet gaming! Mode Switch Position Your System Infrastructure mode (labeled Internet) Left position, which is the factory shipped default Access point or wireless router connected to a wired network Ad-Hoc mode Right position (must be changed from default left position) Small, wireless-only network and all devices have wireless transmitters/ receivers. .................................................................................... Connect the Ethernet cable from your WGE111 Wireless Game Adapter (A) to the Ethernet port (B) in the game console. WGE111WirelessGameAdapterGamingConsoleorotherEthernet-enableddeviceABWGE111WirelessGameAdapterBA Smart Wizard Configuration Assistant You can use the NETGEAR Smart Wizard configuration assistant to change the IP settings of the adapter. Configuring the wireless game adapter to use a fixed or dynamic IP address lets you to access the wireless game adapter configuration from a Web browser. 1. Insert the Resource CD in your CD-ROM drive. Double-click setup.exe if the program does not start automatically. 2. Select Configuration Assistant. The Wireless Game Adapter configuration assistant window shows all the NETGEAR Wireless Game Adapters on the LAN. 3. Select your WGE111 Wireless Game Adapter and click Next. 4. If the password prompt is displayed, type password. 5. Select the Wireless Network you will use from the list. Click Next. 6. Set the Infrastructure or Ad-Hoc configuration mode configuration. If you want to configure Ad-Hoc mode also, select the Ad-hoc Mode check box. You can fill in both sections and the configuration used will be determined by the physical placement of the switch on the back of the wireless game adapter. 7. Enter the security settings used in your network: 2005.03.14 • If your wireless network uses passphrases, enter the passphrase and click Generate to automatically generate they key. • If your network uses manually entered keys, enter the key. Note: Be careful to enter the passphrase or key information accurately. 8. Click Next to proceed. 9. Select the Change Password check box and type the old password for the Wireless Game Adapter. The default password is password. Type a new password and then type it again in the Confirmation box. Click Next. 10. The Wireless Game Adapter Configuration Assistant window shows the TCP/IP settings for the Wireless Game Adapter. a. Change the device name if you like. b. If you are going to use a fixed IP address, select Use this IP Address. Enter the IP address, Subnet mask, and Default gateway to match your network. c. Complete your selections and click Next. 11. The previous settings (if any) and new settings you have configured are displayed. Click Next to proceed. 12. The settings you selected are displayed. Click Refresh to update the results. Click Finish to exit. Troubleshooting If you have trouble setting up your WGE111, check the tips below. You can also consult more extensive troubleshooting procedures in the Reference Manual on the NETGEAR, Inc. Web site at http://kbserver.netgear.co...