Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
For instructions on installing and verifying the Windows 95 network driver, refer to “Install the Windows 95 Network Driver” on the other side of this guide. These three easy steps provide information for installing your Model FA410TX Network Card: 1. Verify Package Contents 2. Install the Network Card 3. Connect the Network Cables As a last step, be sure to fill out and send in your warranty card. Model FA410TX Network Card Installation Giude Verify Package Contents Verify Package Contents Unpack the contents of the package and make sure that you have everything. Model FA410TX Network Card Category 5 10/100 Mbps UTP cable (provided with Model FA410TXC Network Card) Installation guide, Warranty & Drivers and Diagnostics Disk RJ-45 adapter cable Owner Registration Card 8085FA Verify PC Requirements The instructions given in this guide are for using the NETGEAR™ Model FA410TX Network Card in a PC that has a Microsoft® Windows 95 operating system. Model FA410TX Network Card Installation Giude Install the Network Card Install the Network Card The Model FA410TX Network Card is hot swappable, which means it can be inserted into a PC that is either turned off or powered on. 1. Insert the Model FA410TX Network Card into the PCI slot as illustrated in the figure. Some PCs have two PCI slots. The Model FA410TX Network Card can be inserted into either slot. 2. Insert the RJ-45 adapter cable into the connector on the edge of the network card. 3. Turn on the power to the PC, if you have chosen to install the card with the power turned off. Model FA410TX Network Card and RJ-45 adapter cable 8086FA Model FA410TX Network Card Installation Giude Connect the Network Cables Connect the Network Cables Using the UTP cable that is supplied, connect any port on the hub to the port on the network card. Note: One of the ports on NETGEAR hubs is switchable between Normal (MDI-X) and Uplink (MDI) with a Normal/Uplink push button. If you are using this switchable port on a NETGEAR hub to connect to a PC or the network card, make sure the Normal/Uplink push button is set to Normal. RJ-45 connectors PC with network card installed Power adapter Notebook PC *Use the cable provided or any Category 5 UTP cable. Maximum length = 100 meters (300 feet) Category 5 10/100 Mbps UTP cables* Model FA410TX Network Card with RJ-45 adapter cable Hub Model FA410TX Network Card Installation Giude Technical Specifications Technical Specifications Model FA410TX Network Card Standards Compatibility NetWare tested and approved Microsoft Windows, Windows 95, Windows NT® compatible IEEE 802.3i, 10BASE-T Ethernet IEEE 802.3u 100BASE-TX Fast Ethernet Interface Options RJ-45 connector IRQ Options Assigned by Plug-and-Play system Power Consumption 2.0 W Physical Specifications Dimensions 3.37 by 2.13 in. 8.56 by 5.40 cm Weight 0.14 lb (63 g) Environmental Specifications Operating temperature 0° to 45° C Operating humidity 10% to 90% noncondensing Agency Compliance CE mark, commercial FCC, Part 15, Class B EN 55 022 (CISPR 22), Class B Canada ICES-003, Class B Model FA410TX Network Card Installation Giude Install the Network Driver Install the Network Driver This guide provides you with instructions for installing the Windows 95 Network Driver. All versions of Windows 95 might not respond with the same screens. Therefore, windows that are different than those shown in these instructions might open but prompt you for the same information, and windows might open in a different order than the order of the steps in these instructions. Note: You must install the network card (instructions on other side of this guide) before installing the network driver. Before you proceed with the installation steps, decide on a name for your network and for each PC (each name must be only one word). You also need to have the Windows 95 CD-ROM and the FA410TX Drivers and Diagnostics Disk ready to use in the installation process. Note: If the “Insert Disk” window opens and the “Please insert the disk labeled Windows 95...” message appears at any time during the installation process, insert the Windows 95 CD-ROM in Drive D (the CD-ROM drive) and click on “OK.” Then follow the next step in the instructions. If you do not have a CD-ROM drive and are using the Windows 95 floppy disks, insert the requested Windows 95 floppy disk in Drive A, click on “OK,” and then follow the next step in the instructions. Model FA410TX Network Card Installation Giude 1. Turn on power to the computer and start Windows 95. The new hardware is found, and the driver is automatically loaded. Select “Driver from disk provided by hardware manufacturer,” and then click on “OK.” 2. Make sure Drive A is designated on the prompt line (for example, A:\) when the “Copy manufacturer’s files from....” message is displayed. Click on “OK.” 3. OK Network You must provide computer and workgroup names that will identify this computer on the network.i Click on “OK.” Model FA410TX Network Card Installation Giude 4. Enter a name ...
Эта инструкция также подходит к моделям:Сетевое оборудование - FA410TX (470.99 kb)