Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
(Default : Disable) 4.10 Routing These pages define routing related parameters, including static routes and RIP (Routing Information Protocol) parameters. Static route 1-Click "Add" to add a new static route to the list 2-Click "SAVE SETTINGS" to save the configuration RIP parameters 4.11 SET UP WiZARD Getting started RIP sends routing-update messages at regular intervals and when the network topology changes. When a router receives a routing update that includes changes to an entry, it updates its routing table to reflect the new route. RIP routers maintain only the best route to a destination. After updating its routing table, the router immediately begins transmitting routing updates to inform other network routers of the change. Make sure that you have a working ADSL subscription and that the ADSL Wireless Base Station is connected to the ADSL phone line. You can verify that the cable is connected correctly by looking at the ADSL light on the top of the ADSL Wireless Base Station. The ADSL light should be on solid after approximately 1 minute. Wireless settings In step 2 you can change the Wireless settings of the ADSL Wireless Base Station. For easy installation it is advised to keep the default settings. If you later would like to change any of the wireless settings you can do so via the menu in the ADSL Wireless Base Station. Configuring the Wireless ADSL Modem Router ADSL settings In step 3 you have to enter the settings applicable to your ADSL Internet Service Provider (ISP) subscription. For easy installation you can select your ISP from a list of predifined ADSL ISP’s per country. If you cannot find your ISP in the list you can enter the settings manually. To do so select as "Country" "others" and select from the "Internet Service Provider" list the ADSL protocol your ISP is using (this should be mentioned in the documentation you received from your ISP). Confirm Step 4 displays the ADSL settings you’ve entered and that will be used to configure the ADSL Wireless Base Station. Please check that the settings comply with the information you received from your ADSL ISP subscription. If you want to make changes, click the "Back" button to go back to Step 3. After you have clicked "SAVE SETTINGS" the message "Your data is being saved" will appear. Configuring the Wireless ADSL Modem Router Technical data Ports • Four 10/100Mbps Rj-45 Ports • One ADSL RJ-11 ADSL Features • Supports DMT line modulation • Supports Annex A Full-Rate ADSL : up to 8 Mbps downstream, up to 1 Mbps upstream (G.992.1 & TI.143, Issue 2) • Supports G.Lite ADSL : up to 1.5 Mbps downstream, up to 512 Kbps upstream • Dying GASP support ATM Features • RFC1483 Encapsulation (IP, Bridging and encapsulated routing) • PPP over ATM (LLC & VC multiplexing) (RFC2364) • Classical IP (RFC1577) • Traffic shaping (UBR, CBR) • OAM F4/F5 support • PPP over Ethernet Client Management Features • Firmware upgrade via web based management • Web based management (configuration) • Power indicators • Event and history logging • Network ping Security Features • Password protected configuration access • User authentication (PAP/CHAP) with PPP • Firewall NAT NAPT • VPN pass through (IPSec-ESP Tunnel mode, L2TP, PPTP) Wireless Security • WEP 64/128 bit • WPA/WPA2 • WPA/WPA2-Personal (PSK) • WPA-PSK with TKIP • WPA2-PSK with AES • WPA-PSK + WPA2-PSK with TKIP+AES.AES, or TKIP • WPS : PIN and PBC methods LAN Features • IEEE 802.1d (self-learning transparent Bridging) • DHCP Server • DNS Proxy • Static Routing, RIPv1 and RIP Radio Features • Wireless RF module Frequency Band • 802.11n Radio : 2.4GHz • 802.11g Radio : 2.4GHz • 802.11b Radio : 2.4GHz Europe - ETSI • 2412~2472MHz (Ch1~Ch13) Modulation Type • 802.11n Draft-2.0 : OFDM (BPSK, QPSK, 16- and 64-QAM) • 802.11g : OFDM (BPSK, QPSK, 16- and 64-QAM) • 802.11b : CCK (11 Mbps, 5.5 Mbps), DQPSK (2 Mbps) Operating Channels IEEE 802.11n • 13 channels (ETSI) Operating Channels IEEE 802.11g • 13 channels (ETSI) Operating Channels IEEE 802.11b • 13 channels (Europe) Transmit Power and Sensitivity TX Output Power : (Typical) • 802.11b : 18.5 +/- 1dBm • 802.11g : 14.5 +/- 1dBm@54Mbps • 802.11n : 14.5 +/- 1dBm RX Sensitivity : (Typical) • -84 dBm@11Mbps • -72 dBm@54Mbps • -64 dBm@64-QAM, 20MHz channel spacing • -61 dBm@64-QAM, 40MHz channel spacing Environmental Complies with the following standards : Temperature : IEC 68-2-14 • 0 to 40 degrees C (Standard Operating) • -20 to 70 degrees C (non-operation) Humidity • 5% to 95% (non-condensing) Vibration • IEC 68-2-36, IEC 68-2-6 Shock • IEC 68-2-29 Drop • IEC 68-2-32 Input Power • 15V 0.8A IEEE standards • IEEE 802.3, 802.3u, 802.11g, 802.1d • IUT G.dmt • IUT G.Handshake • IUT T.413 issue 2 - ADSL full rate Standards Conformance Electromagnetic Compatibility • CE, ETS 300 328, ETS 300 836 (Wireless) • EN50081, EN50082, EN61000-3-2, EN61000-3-3 (EMC) • Vista, WPS Safety • EN60950 Technical data Frequently asked questions In this chapter you will find the most frequently...