Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
Power on/off switch • Press the on/off POWER button (figure A-4, B-10) to switch on the unit. A green A-5, B-11) on the right-hand side of the button lights up to show that the unit is on. Input selection buttons The input signal selection buttons (figure B-14) on the Transmitter unit select the signal that is shown on the second TV (TV2). • Press the input selection button “ INPUT 1” on the Transmitter unit to select the video sour video sourvideo sourvideo sourvideo sourvideo source cecececece connected to the “ SCART IN 1” connector. • Press the input selection button “ INPUT 2” on the Transmitter unit to select the video sour video sourvideo sourvideo sourvideo sourvideo source cecececece connected to the “ SCART IN 2” connector. Transmission channel selection switch To allow you to enjoy the best possible performance, the Philips Wireless TV Link is equipped with a transmission channel switch. You can switch between four channels (or less, depending on local regulations) to select the one that offers the best possible performance with minimum or no interference. Please note that in all cases both the Transmitter unit and Receiver unit should be switched to the same channel. • Change channel on the Transmitter unit (figure B-8). • Select the same channel on the Receiver unit (figure A-2). Note Always select the same channel on both the Transmitter unit and Receiver unit. + Operation How to watch and • Switch on the video sour video sourvideo sourvideo sourvideo sourvideo source cecececece. • Switch on the main TV • Select the SCART input (EXT or AV) on the main TV (see TV • Control the video source either directly or by using the video source’s remote control. Note The ‘ automatic input selector function’ of the main TV is overruled by the Transmitter unit + so that programmes on the main TV are controlled via the second TV. How to watch and operate video sources on • Switch on the video sour video sourvideo sourvideo sourvideo sourvideo source cecececece. • Switch on the Transmitter unit (figure B-10). • Use the input selection buttons (figure B-14) to select either • If you wish, bring the video sour video sourvideo sourvideo sourvideo sourvideo source cecececece’ ’’’’’s sssss remote control with you to your second TV (TV2) to control the video sour video sourvideo sourvideo sourvideo sourvideo source cecececece. • Switch on the Receiver unit (figure A-4). • Switch on the second TV. • Select the SCART input (EXT or AV) on the second TV (see TV instruction manual) . • Control the video source using the video source’s remote control by aiming the remote control at the Receiver unit. Note It is not necessary to switch on your main TV to enjoy video programmes on your second + TV. For even greater controlling convenience of your second TV use a Philips universal remote + control. How to watch cable programmes on your second TV (TV2) without running a cable • Switch on your VCR • Select your VCR as the video source for the Wireless TV Link. (figure A-14, “ INPUT 1” or “ INPUT 2” ) • Select the programme you want to watch on your VCR (Programme UP / DOWN on your VCR or via remote control). Normally you will have programmed the order of programmes to correspond with the programmes on your main TV. • From your second TV you can use the VCR’s remote control (or a universal remote control, set to VCR) to select the programme you want to watch (Programme UP / DOWN). • The second TV should remain at the EXTERNAL AV (SCART) input. • From your second TV you can start watching the video tape by pressing PLAY on the VCR’s remote control (or a universal remote control, set to VCR). Note The VCR must be connected to the cable TV network and to the Philips Wireless TV Link. + 4 5 Testing Step 1: testing the You should now see It may be necessary reposition the Receiver Repositioning the Transmitter unit, centimetre by centimetre over the surface on which it’s positioned, can also help to Step 2: testing the remote control Try out the remote control to make sure correctly. Point the remote control of the video source you are watching at the Receiver unit Play and then Stop. A red light (figure A-7) the remote control command. On the Transmitter unit a red light (figure B-13) flashes to indicate that it is sending the extended remote control command If no red light flashes on the Transmitter unit it may be necessary to reposition either of the remote control antennas on the rear of the Receiver unit (figure A-8) or Transmitter unit (figure B-15). The red light on the Transmitter unit should now flash when a remote control the receiver. If the video sour video sourvideo sourvideo sourvideo sourvideo source cececececedoes not respond to the given remote control command please control extender cord. Installing the remote control extender cord A cord with two IR eyes and a jack plug is provided to deliver the signals from unit to the video sources you wish to control. • Ensure that the Transmitter unit is switched off. • Plug...