Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
For more information on VLANs and router ports, see Chapter 21, “VLAN Management Commands.” • RIPng will support a maximum of 20 interfaces. Example -> ipv6 rip interface Test_Lab Release History Release 5.1.6; command was introduced. page 2-64 Release 5.1.6.R02 User Guide Supplement June 2005 IPv6 Commands ipv6 rip interface Related Commands ipv6 load rip Loads RIPng into memory. ipv6 rip status Enables/disables RIPng on the switch. ipv6 rip interface recv-status Configures IPv6 RIPng interface “Receive” status. When this status is set to "enable", packets can be received on this interface. ipv6 rip interface send-status Configures IPv6 RIPng interface “Send” status. When this status is set to "enable", packets can be sent on this interface. show ipv6 rip interface Displays information for all or specified RIPng interfaces. MIB Objects alaRipngInterfaceTable alaRipngInterfaceStatus Release 5.1.6.R02 User Guide Supplement June 2005 page 2-65 ipv6 rip interface metric IPv6 Commands ipv6 rip interface metric Configures the RIPng metric or cost for a specified interface. You can set priorities for routes generated by a switch by assigning a metric value to routes generated by that switch’s RIPng interface. For example, routes generated by a neighboring switch may have a hop count of 1. However, you can lower the priority of routes generated by that switch by increasing the metric value for routes generated by the RIPng interface. ipv6 rip interface if_name metric value Syntax Definitions if_name value IPv6 interface name. Metric value. Valid range is 1 - 15. Defaults parameter value default 1 Platforms Supported OmniSwitch 6624, 6648, 7700, 7800, 8800 Usage Guidelines When you configure a metric for a RIPng interface, this metric cost is added to the metric of the incoming route. Example -> ipv6 rip Test_Lab metric 1 Release History Release 5.1.6; command was introduced. Related Commands ipv6 rip interface Creates/deletes a RIPng interface. show ipv6 rip interface Displays information for all or specified RIPng interfaces. MIB Objects alaRipngInterfaceTable alaRipngInterfaceMetric page 2-66 Release 5.1.6.R02 User Guide Supplement June 2005 IPv6 Commands ipv6 rip interface recv-status ipv6 rip interface recv-status Configures IPv6 RIPng interface “Receive” status. When this status is set to "enable", packets can be received on this interface. When it is set to "disable", packets will not be received on this interface. ipv6 rip interface if_name recv-status {enable | disable} Syntax Definitions if name enable | disable IPv6 interface name. Interface “Receive” status. Defaults parameter enable | disable default enable Platforms Supported OmniSwitch 6624, 6648, 7700, 7800, 8800 Usage Guidelines RIPng must be loaded (ipv6 load rip) and enabled (ipv6 rip status)on the switch to send or receive packets on the interface. Example -> ipv6 rip interface Test_Lab recv-status disable Release History Release 5.1.6; command was introduced. Related Commands ipv6 load rip Loads RIPng into memory. ipv6 rip status Enables/disables RIPng on the switch. ipv6 rip interface send-status Configures IPv6 RIPng interface “Send” status. MIB Objects alaRipngInterfaceTable alaRipngInterfaceRecvStatus Release 5.1.6.R02 User Guide Supplement June 2005 page 2-67 ipv6 rip interface send-status IPv6 Commands ipv6 rip interface send-status Configures IPv6 RIPng interface “Send” status. When this status is set to "enable", packets can be sent from this interface. When it is set to "disable", packets will not be sent from this interface. ipv6 rip interface if_name send-status {enable | disable} Syntax Definitions if name enable | disable IPv6 interface name. Interface “Send” status. Defaults parameter enable | disable default enable Platforms Supported OmniSwitch 6624, 6648, 7700, 7800, 8800 Usage Guidelines RIPng must be loaded (ipv6 load rip) and enabled (ipv6 rip status)on the switch to send or receive packets on the interface. Example -> ipv6 rip interface Test_Lab send-status enable Release History Release 5.1.6; command was introduced. Related Commands ipv6 load rip Loads RIPng into memory. ipv6 rip status Enables/disables RIPng on the switch. ipv6 rip interface recv-status Configures IPv6 RIPng interface “Receive” status. MIB Objects alaRipngInterfaceTable alaRipngInterfaceSendStatus page 2-68 Release 5.1.6.R02 User Guide Supplement June 2005 IPv6 Commands ipv6 rip interface horizon ipv6 rip interface horizon Configures the routing loop prevention mechanisms. ipv6 rip interface if_name horizon {none | split-only | poison} Syntax Definitions if_name IPv6 interface name. none | split-only | poison none -Disables loop prevention mechanisms. split-only - Enables split-horizon, without poison-reverse. poison - Enables split-horizon with poison-reverse. Defaults parameter default none | split-only | poison poison Platforms Supported OmniSwitch 6624, 6648, 7700, 7800, 8800 Usage Guidelines • If set to “none” the route is not sent back to the peer....
Эта инструкция также подходит к моделям:Сетевое оборудование - 6600 (685.69 kb)
Сетевое оборудование - 7700 (685.69 kb)