Войти:
Оценок - 1, средний балл: 3 ( )

Инструкция по эксплуатации Adaptec, модель AHA-1520A

Производитель: Adaptec
Размер: 270.83 kb
Название файла:
Язык инструкции:
Перейти к скачиванию



К этому устройству также есть другие инструкции:

Фрагмент инструкции


ID 7 has the highest priority, and ID 0 has the lowest. Setting SCSI IDs is a two-step process: 1 Determine the ID of each device on the SCSI bus. The default ID for the AHA-1510A/20A is ID 7. To determine the IDs of disk drives, CD-ROM drives, and other devices, read their documentation and examine their switch settings or jumper settings. 2 Change the IDs (if needed) so that no IDs are duplicated on the same host adapter. We recommend the following IDs: – Leave the AHA-1510A/20A at the default, SCSI ID 7. – If you are installing Floptical drives, set them to SCSI IDs 2 through 6. – If you want to boot your computer from a SCSI hard disk drive, set the drive ID to 0. See the SCSI device documentation for instructions on changing the SCSI ID. Inserting the Host Adapter in a Slot WARNING: Be sure the power is turned OFF before you continue. Also, ground yourself by touching an unpainted surface on the computer chassis before you open the computer case. 1 Remove the cover from the computer case. 2 Locate an unused, unobstructed expansion slot. 3 Remove the corresponding expansion slot cover from the back of the computer chassis. (The slot cover is the metal strip that covers the opening through which the host adapter’s external connector extends.) Keep the screw that held the metal strip in place; you will need it later. AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAHA-1510A/20A Series User’s Guide A AA AA AStock Number: 510400-00, Rev. C Page: 3-5 A AA AA APrint Spec Number: 491842-00 A AA AA ACurrent Date: 11/18/94 ECN Date: 11/29/94 A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AHA-1510A/20A Series User’s Guide 4 Ground yourself by touching an unpainted surface on the computer chassis, then carefully remove the host adapter from its package. 5 Position the host adapter directly over the slot. If your computer has a card guide to align the host adapter, be sure to insert the end of the board in the card guide. 6 Carefully press the bus connector on the bottom of the host adapter down into the slot, as shown in Figure 3-5, until the metal contacts on the bottom of the host adapter are securely seated in the slot. Figure 3-5. Inserting the Host Adapter in a Slot Attach the host adapter bracket to the computer chassis with the screw from the expansion slot cover that you removed. Note: Do not put the computer cover back on or reconnect the power yet! AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAHA-1510A/20A Series User’s Guide A AA AA AStock Number: 510400-00, Rev. C Page: 3-6 A AA AA APrint Spec Number: 491842-00 A AA AA ACurrent Date: 11/18/94 ECN Date: 11/29/94 A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA Hardware In...

Эта инструкция также подходит к моделям:
Сетевое оборудование - AHA-1510A (270.83 kb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории