Оценок - 4, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
Install in any available 64-bit PCI slot. Dell recommends installing Emulex cLAN adapters in PCI slot 3, 4, or 5. If you are currently using a DRAC II or plan to use one in the future, install the DRAC II in PCI slot 7. Bus 3: PCI slots 1 and 2 are 64 bit, 66 MHz. 2550 Bus 1: PCI slots 1, 2, and 3 are 64 bit, 33 MHz. Install in any available PCI slot. If you are not currently using a DRAC II and do not plan to use one in the future, Dell recommends NOTE: The Broadcom NIC drivers in your cluster node must be one of the following versions: • Windows 2000 Advanced Server—version 2.43 or later • Windows NT Server 4.0, PCI slot 2 is dedicated to interface with the optional DRAC II. that you install one RAID controller in the 32-bit Enterprise Edition—version 2.46 or later slot, even if the RAID controller is a 64-bit controller. The Broadcom NIC firmware version must be 1.12 or later. The integrated Broadcom NIC firmware revisions were created in ascending order, starting with version 1.1 and ending with 1.12 or later. Consequently, version 1.2 is an earlier version than version 1.12. To upgrade the firmware, at the prompt, type upgf x boot y where x is the device number of the integrated Broadcom NIC and y is the drive letter of where the firmware file is located. The utility upgrades the integrated NIC firmware in your system. The driver and utility to upgrade the firmware are available on the Dell Support website at support.dell.com. Platform Guide | support.dell.com Table 1-3. PCI/PCI-X Slot Assignments for PowerEdge Cluster Nodes (continued) PowerEdge PCI Buses RAID Controller NICs DRAC II or III System 2600 PCI slot 1 is 32 bit, 33 MHz. Bus 2: PCI/PCI-X slot 7 is hotpluggable 64 bit, up to 133 MHz. Bus 3: PCI/PCI-X slot 6 is hotpluggable 64 bit, up to 133 MHz. Bus 4: PCI/PCI-X slots 4 and 5 are hot-pluggable 64 bit, up to 100 MHz. Bus 5: PCI/PCI-X slots 2 and 3 are hot-pluggable 64 bit, up to 100 MHz. Install in any available Install in any available PCI slot. NA PCI slot. NOTE: Install PERC 3/DC and PERC 3/QC expansion cards in PCI-X expansion card slots 2–5. Dell recommends that you do not install PERC 3/DC and PERC 3/QC expansion cards in slots 6 and 7. 2650 Three 64-bit PCI/PCI-X slots are located on the riser card (two slots on bus 1 and one slot on bus 2). Slots accept full-length cards designed for PCI-X up to 133 MHz. Install in any available Install in any available 64-bit PCI slot. NA PCI slot. NOTE: For systems using Windows NT 4.0, Enterprise Edition, adding and removing a PERC 3/DC expansion cards requires that drivers for the onboard NIC be installed. 4400 Bus 1: PCI slots 1 Install in any available Install in any available PCI slot. If you are currently and 2 are 64 bit, 64-bit, 33-MHz or 32-bit, using a DRAC II Dell recommends installing Emulex 33/66 MHz. 33-MHz PCI slot. or plan to use one cLAN adapters in 64-bit slots. in the future, Bus 2: PCI slots 3 install the DRAC through 6 are II in PCI slot 7. 64 bit, 33 MHz. Bus 3: PCI slot 7 is 32 bit, 33 MHz. 1-6 Platform Guide Table 1-3. PCI/PCI-X Slot Assignments for PowerEdge Cluster Nodes (continued) PowerEdge System 4600 PCI Buses PCI slot 1 is 32 bit, 33 MHz. Bus 1: PCI/PCI-X slots 2 and 3 are hot-pluggable 64 bit, up to 100 MHz. Bus 2: PCI/PCI-X slots 4 and 5 are hot-pluggable 64 bit, up to 100 MHz. Bus 3: PCI/PCI-X slots 6 and 7 are hot-pluggable 64 bit, up to 100 MHz. RAID Controller Install in any available 64-bit, 33-MHz or 32-bit, 33-MHz PCI slot. NICs Install in any available PCI slot. DRAC II or III If you are currently using a DRAC III or plan to use one in the future, install the DRAC III in PCI slot 1. 6400 Bus 1: PCI slot 1 is 32 bit, 33 MHz. Bus 2: PCI slots 2 through 5 are 64 bit, 33 MHz. Bus 3: PCI slots 6 and 7 are 64 bit, 33/66 MHz. Install in any available 32-bit, 33-MHz or 64-bit, 33-MHz PCI slot. Install in any available PCI slot. Dell recommends installing Emulex cLAN adapters in 64-bit slots. If you are currently using a DRAC II or plan to use one in the future, install the DRAC II in PCI slot 1. 6450 Bus 1: PCI slot 1 is 32-bit, 33 MHz. Bus 2: PCI slots 2 through 5 are 64 bit, 33 MHz. Bus 3: PCI slots 6 and 7 are 64 bit, 33/66 MHz. Install in any available 32-bit, 33-MHz or 64-bit, 33-MHz PCI slot. Install in any available PCI slot. Dell recommends installing Emulex cLAN adapters in 64-bit slots. If you are currently using a DRAC II or plan to use one in the future, install the DRAC II in PCI slot 1. Platform Guide | support.dell.com Table 1-3. PCI/PCI-X Slot Assignments for PowerEdge Cluster Nodes (continued) PowerEdge PCI Buses RAID Controller NICs DRAC II or III System 6600 Bus 1: PCI slot 1 is 32 bit, 33 MHz. Install in any available slot. Install in any available slot. If you are currently using a DRAC III Bus 2: PCI/PCI-X slots 2 and 3 are 64 bit, up to 100 MHz. or plan to use one in the future, install the DRAC III in PCI slot 1. Bus 3: PCI/PCI-X slots 5, 6, and 7 are 64 bit, up to 10...
Эта инструкция также подходит к моделям:Сетевое оборудование - SE400 (781.56 kb)