Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Part Number Description E7484-60029 800 MHz for CDMA, iDEN E7484-60027 1800 MHz GSM E7484-60028 1900 MHz for CDMA, GSM E7484-60026 900 MHz GSM All cables are labeled to indicate whether the cable is for voice only or for voice and data. The labels also reflect both part number and Agilent option number. Agilent E6474A User’s Guide System Information Agilent receivers Part Number Description Available Options E6450C PCS CDMA/TDMA receiver, 1.9GHz E6451C GSM receiver, 900 MHz E6452C Cellular CDMA/TDMA receiver, 850 MHz E6457C Cellular CDMA/TDMA receiver, 800 MHz, Japan cellular band E6453C GSM/Korean band CDMA receiver, 1.8GHz E6454C PCS CDMA/GSM receiver, 1.9GHz E6455C IMT-2000 band W-CDMA (UMTS) / CDMA receiver, 2.1 GHz (with GPS) E6456C W-CDMA/UMTS/cdma2000, 1.9 GHz (with GPS) E6458C GSM850 Receiver (with GPS) Hardware included with E6474A software licenses E6473B hardware options are typically ordered with Agilent E6474A system. E6474A software option licenses include the following hardware items: Component Part Number Description Software license key for Parallel port E6474-10002 Can be programmed with the E6474A software options that you have ordered using the License Manager software. Plugs into the computer’s Parallel port. Software license key for USB port E6474-10003 Contains the E6474A software options that you have ordered. Plugs into the computer’s USB port. Dual serial port PCMCIA card 1150-2067 Plugs into the computer’s PCMCIA card slot. Used if a device is connected directly to the computer. Agilent E6474A User’s Guide 169 System Information Agilent E6474A User’s Guide Agilent E6474A User’s Guide WARNING D Permanent In-Vehicle Hardware Installation Before installing this product, check your vehicle warranty for any special instructions regarding the installation of third party products. Agilent assumes no responsibility for any vehicle warranty issues arising out of the installation or use of this product. It is recommended that any vehicle installation should be done by a qualified vehicle mechanic and electrician. To install this See this Direct connect hub “Direct Connect Hub Installation" on page 174 Antenna “Antenna Installation" on page 175 Computer mount “Computer mount installation" on page 176 Cables “Cable Installation" on page 177 Agilent Technologies D Permanent In-Vehicle Hardware Installation Installation Guidelines WARNING Use the following guidelines for installing the system hardware. • The dimensions of the in-vehicle rack with the navigator installed are approximately: • Width: 11 inches / 280 mm • Depth: 10.5 inches / 265 mm (allow an additional 3 inches / 76 mm for handles) • Height (with E746xx): 6.5 inches / 164 mm • Because every installation has different requirements, the installer must select the appropriate mounting hardware. • If you are using a permanently installed antenna, follow the antenna manufacturer’s installation instructions. Antennas should be spaced at least 18” apart to avoid interference. Choose suitable locations for the navigator and E6473B, the phones, the speakers, and the computer, that will not interfere with the operation of the vehicle, but will allow access to the cable connectors. If the system includes an E645xx receiver, allow room for its mounting plate. Observe local regulations and restrictions when installing the equipment and making electrical connections to the vehicle. Use caution when drilling holes and working around critical areas, such as the fuel tank, fuel lines, battery, engine compartment, electrical harnesses, fuse block, and the exhaust system. Disconnect the battery before making permanent connections to the electrical system. Agilent E6474A User’s Guide Permanent In-Vehicle Hardware Installation D CAUTION Secure all components to prevent movement while the vehicle is in motion. When routing cables leave sufficient length on both ends for making connections. Avoid sharp metal edges, sharp bends, and crushing the cables. Use a rubber grommet if the cable is routed through a hole in a metal panel. Do not route a cable near the catalytic converter. Use wiring troughs when they are available. Agilent E6474A User’s Guide D Permanent In-Vehicle Hardware Installation Direct Connect Hub Installation Use the following guidelines for installing the E6473B hub in your vehicle: Choose a suitable location for the in-vehicle chassis - you must have access to the front and back of the unit. The location must be flat and capable of taking the four locating screws/bolts (refer to Figure 66). Figure 66 In-Vehicle rack for direct connect hub Mounting the E645x receiver Use the following guidelines for installing the Agilent E645x receiver: • Locate a flat surface of the vehicle to which the base plate can be securely attached. • Attach the base plate to the vehicle using the hardware provided. Agilent E6474A User’s Guide Permanent In-Vehicle Hardware Installation D Antenna Installation Installation guidelines • All antennas must be spaced a...