Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
All the addresses learned by monitoring traffic are stored in the dynamic address table. You can also manually configure static addresses that are bound to a specific port. Setting Static Addresses A static address can be assigned to a specific interface on this switch. Static addresses are bound to the assigned interface and will not be moved. When a static address is seen on another interface, the address will be ignored and will not be written to the address table. Command Attributes • Static Address Counts1 – The number of manually configured addresses. • Current Static Address Table – Lists all the static addresses. • Interface – Port or trunk associated with the device assigned a static address. • MAC Address – Physical address of a device mapped to this interface. • VLAN – ID of configured VLAN (1-4093). Web – Click Address Table, Static Addresses. Specify the interface, the MAC address and VLAN, then click Add Static Address. Figure 21-1 Static Addresses 1. Web Only. 21 Address Table Settings CLI – This example adds an address to the static address table, but sets it to be deleted when the switch is reset. Console(config)#mac-address-table static 00-e0-29-94-34-de interface ethernet 1/1 vlan 1 delete-on-reset 50-1 Console(config)# Displaying the Address Table The Dynamic Address Table contains the MAC addresses learned by monitoring the source address for traffic entering the switch. When the destination address for inbound traffic is found in the database, the packets intended for that address are forwarded directly to the associated port. Otherwise, the traffic is flooded to all ports. Command Attributes • Interface – Indicates a port or trunk. • MAC Address – Physical address associated with this interface. • VLAN – ID of configured VLAN (1-4093). • Address Table Sort Key – You can sort the information displayed based on MAC address, VLAN or interface (port or trunk). • Dynamic Address Counts – The number of addresses dynamically learned. • Current Dynamic Address Table – Lists all the dynamic addresses. Displaying the Address Table 21 Web – Click Address Table, Dynamic Addresses. Specify the search type (i.e., mark the Interface, MAC Address, or VLAN checkbox), select the method of sorting the displayed addresses, and then click Query. Figure 21-2 Dynamic Addresses CLI – This example also displays the address table entries for port 1. Console#show mac-address-table interface ethernet 1/1 50-3 Interface Mac Address Vlan Type --------- ----------------- ---- ---------------- Eth 1/ 1 00-E0-29-94-34-DE 1 Permanent Eth 1/ 1 00-20-9C-23-CD-60 2 Learned Console# 21 Address Table Settings Changing the Aging Time You can set the aging time for entries in the dynamic address table. Command Attributes • Aging Status – Enables/disables the aging function. • Aging Time – The time after which a learned entry is discarded. (Range: 10-1000000 seconds; Default: 300 seconds) Web – Click Address Table, Address Aging. Specify the new aging time, click Apply. Figure 21-3 Address Aging CLI – This example sets the aging time to 400 seconds. Console(config)#mac-address-table aging-time 400 50-4 Console(config)# Chapter 22: Spanning Tree Algorithm Configuration The Spanning Tree Algorithm (STA) can be used to detect and disable network loops, and to provide backup links between switches, bridges or routers. This allows the switch to interact with other bridging devices (that is, an STA-compliant switch, bridge or router) in your network to ensure that only one route exists between any two stations on the network, and provide backup links which automatically take over when a primary link goes down. Overview The spanning tree algorithms supported by this switch include these versions: • STP – Spanning Tree Protocol (IEEE 802.1D) • RSTP – Rapid Spanning Tree Protocol (IEEE 802.1w) • MSTP – Multiple Spanning Tree Protocol (IEEE 802.1s) STP – STP uses a distributed algorithm to select a bridging device (STP-compliant switch, bridge or router) that serves as the root of the spanning tree network. It selects a root port on each bridging device (except for the root device) which incurs the lowest path cost when forwarding a packet from that device to the root device. Then it selects a designated bridging device from each LAN which incurs the lowest path cost when forwarding a packet from that LAN to the root device. All ports connected to designated bridging devices are assigned as designated ports. After determining the lowest cost spanning tree, it enables all root ports and designated ports, and disables all other ports. Network packets are therefore only forwarded between root ports and designated ports, eliminating any possible network loops. x Designated Root Designated PortDesignated Bridge x x x Root Port x Once a stable network topology has been established, all bridges listen for Hello BPDUs (Bridge Protocol Data Units) transmitted from the Root Bridge. If a bridge does not get a Hello BPDU after a predefined interva...
Эта инструкция также подходит к моделям:Сетевое оборудование - Direk Tronik 24/48-Port (4.82 mb)
Сетевое оборудование - Direk Tronik ES4548D (4.82 mb)