Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
Harsh temperature conditions, vibration, dust, etc. all put higher demands on the quality and reliability of your networking equipment. To survive harsh industrial environments, Alloy provides you with the RNS5/8 Series Industrial 5-port/8-port 10/100Mbps Ethernet Switches. The RNS5/8 Industrial switch is a cost-effective solution ideal for your industrial applications in harsh environments. The RNS5/8 not only gives you high speed data transmission over an Ethernet network, but also provides redundant power inputs and reverse polarity protection. In addition, the RNS5/8 is manufactured in an IP30 aluminum case, and has passed several safety certifications, ensuring customers a cost-effective, safe, and reliable industrial device. Features .. 5-port /8-port 10/100T(X) industrial switch .. Supports store-and-Forward switching architecture .. Supports IEEE 802.3 10Base-T, 802.3u 100Base-TX standard .. Supports auto MDI/MDI-X function .. RNS5: 512 KB embedded memory .. RNS8: 1024KB embedded memory .. Supports IEEE 802.3x flow control .. Flow control for full-duplex mode .. Back pressure for half-duplex mode .. Provides redundant dual power inputs .. Aluminum case with IP30 protection .. RNS5:1K MAC address table .. RNS8:2K MAC address table .. DIN-Rail and wall mountable design Package Checklist Alloy RNS5/8 Industrial 5-port/8-port Ethernet Rail Switches are packaged with the following items: .. RNS5/8 Industrial 5-port/8-port Ethernet Rail Switch .. One DIN-Rail clip (attached to the RNS5/8) .. One wall mounting plate and six screws .. User’s manual CD-ROM RNS5/8 Switch User’s Manual CD-ROM Wall Mounting Plate Screws DIN-Rail Clip Contact your sales representative if any item is missing or damaged. Hardware Description Dimensions RNS5/8 Industrial 5-port/8-port Ethernet Rail Switch dimensions (W x H x D) are 54mm x 135mm x 105mm Front Panel The Front Panel of the RNS5 Industrial 5-port Ethernet Rail Switch is shown in Figure A. Figure A. Front Panel of the RNS5 Industrial 5-port Ethernet Rail Switch LED Indicators UTP Ports The Front Panel of the RNS8 Industrial 8-port Ethernet Rail Switch is shown in Figure A. Figure A. Front Panel of the RNS8 Industrial 8-port Ethernet Rail Switch LED Indicators UTP Ports Bottom View The bottom view of the RNS5/8 Industrial 5-port/8-port Ethernet Rail Switch consists of one terminal block connector with two DC power inputs, Alarm output and one DC IN power jack for an additional AC/DC power adapter. Figure B. Bottom view of the RNS5/8 Industrial 5-port/8-port Ethernet Rail Switch Wiring the DC Power Inputs Follow the steps below to wire RNS5/8 dual DC power inputs. [Note] The suitable electric wire ranges from 12 to 24 AWG. V- V+ V- V+ [Note] The additional power jack is designed for office use. 1. Insert the positive and negative wires into the V+ and V- contacts respectively of the terminal block connector 2. Tighten the wire-clamp screws to prevent the DC wires from being loosened. LED Indicators There are 5 diagnostic LEDs and 8 Port LEDs located on the Front panel of the RNS5 Industrial Ethernet Rail Switch. These LED indicators provide administrators with real-time system status. Table 1 gives descriptions of the functions of each LED indicator. LED Status Description PWR Green Power is on. Off No power is being supplied. PWR 1 Green Power is on. Off No power is being supplied. PWR 2 Green Power is on. Off No power is being supplied. LNK/ACT of Port 5 Green A network device is detected. Blinks The port is transmitting or receiving packets from the TX device. Off No device is attached. FDX/COL of Port 5 Orange The port is operating in full-duplex mode. Blinks Collision of packets occurs. Off The port is in half-duplex mode or no device is attached. Port LED Status Description Port Status (Port 1 to Port 4) Orange The port is operating in full-duplex mode. Blinking orange Collision of Packets occurring. Off The port is in half-duplex mode or no device is attached. Green A network device is detected. Blinking green The port is transmitting or receiving packets from the TX device. Off No device is attached. Table 1 There are 7 diagnostic LEDs and 12 Port LEDs located on the Front panel of RNS8 Industrial Ethernet Rail Switch. These LED indicators provide administrators with real-time system status. Table 2 gives descriptions of the function of each LED indicator. LED Status Description PWR Green Power is on. Off No power is being supplied. PWR 1 Green Power is on. Off No power is being supplied. PWR 2 Green Power is on. Off No power is being supplied. LNK/ACT of Port 7/8 Green A network device is detected. Blinks The port is transmitting or receiving packets from the TX device. Off No device is attached. FDX/COL of Port 7/8 Orange The port is operating in full-duplex mode. Blinks Collision of packets occurs. Off The port is in half-duplex mode or no device is attached. Port LED Status Description Port Status (Port 1 to Port 6) Orange The port is operating in full-duplex ...
Эта инструкция также подходит к моделям:Сетевое оборудование - RNS8 (668.25 kb)