Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
If any item is missing, please contact the dealer from whom the equipment was purchased. • Wireless Broadband Router x1 • Power Adapter and Cord x1 • CD x1 • RJ-45 Ethernet Cable x1 • Quick Installation Guide x1 1.4 System Requirements • Cable/ADSL modem and an Internet access account for Internet connection • One computer with 10/100Base-T Ethernet card and TCP/IP protocol installed for initial setup • Internet Explorer 5.0 or higher for Web configuration • 802.11g or 802.11b compliant wireless adapters (for wireless connection) 2 Hardware Description & Installation 2.1 Physical Outlook Front Panel The following illustration shows the front panel of the Wireless Broadband Router: Figure 2-1 LED Indicator LED Indicator The Wireless Broadband Router is equipped with seven LEDs on the front panel as described in the table below (from left to right): LEDs Color Status Description PWR Green Off No power is supplied to the unit. Solid Power is connected to the unit. Off WLAN interface is not initialized properly. WLAN Green On WLAN interface is initialized properly and ready. Blinking Transmitting/receiving packets wirelessly. LAN 1-4 Green/Amber Off No Ethernet device is connected. Wireless Broadband Router User Manual LEDs Color Status Description Solid Ethernet connection is established. · Amber - 100 Mbps Ethernet connection · Green - 10 Mbps Ethernet connection. Blinking Transmitting/receiving packets on the LAN port. Off Power is off or no broadband device is connected. WAN Green On Broadband device is connected. Blinking Transmitting/receiving packets on the WAN port. Rear Panel and Connector The following figure illustrates the rear panel of the Wireless Broadband Router. Figure 2-2 Rear Panel and Connector • DC 5V: Power connector • LAN Ports 1-4: RJ-45 Connector. Integrated 4-port 10/100BaseT switch. Connects to a hub, switch or NIC- equipped PC in your network. The LAN ports has Auto- MDI/MDIX feature that supports either crossover or straight-through cables. • WAN: RJ-45 connector. Connects to the Cable/ADSL Modem. The WAN port also has Auto-MDIX feature that supports either crossover or straight-trough cables. • reset: Dual-function button: Wireless Broadband Router User Manual • Reboot. Insert a straightened paperclip into the reset hole to press the button. This will reboot the Wireless Broadband Router. • Restore to the factory defaults. Insert a straightened paperclip into the reset hole to press the button. Keep pressing and power cycle (off and on) the device. Wait for at least 5 seconds to release the button. Then wait for the device to finish booting. This operation erases all previous settings entered by the administrator. 2.2 Hardware Connection Choosing a Place for the Wireless Broadband Router • Place the device close to the power outlet for the cable to reach it easily. • Avoid placing the device in places where people may walk on the cables. • Keep the device away from direct sunlight or heat sources. • Place the device on a flat and stable stand. Wireless Broadband Router User Manual Connecting the Wireless Broadband Router Prior to connecting the hardware, make sure to power off your Ethernet device, Cable/ADSL modem and Wireless Broadband Router. Then follow the steps below to connect the related devices. Step 1 Connecting wired device to the LAN port. Attach one end of the Ethernet cable with RJ-45 connectors to your hub, switch or a PC’ s Ethernet port, and the other end to the LAN port of the Wireless Broadband Router. Step 2 Connecting Cable/ADSL Modem to the WAN port. Connect the Ethernet cable attaching to your Cable/ADSL modem to the WAN port of your Wireless Broadband Router. Step 3 Connecting the power adapter. Connect the single DC output connector of the power adapter to the power jack on the back of the Wireless Broadband Router. Then connect the supplied power cord to the power adapter and the other end to an AC outlet. Only use the adapter supplied with the Wireless Broadband Router. Connecting another adapter can cause permanent damage to the device. Caution Wireless Broadband Router User Manual The figure below illustrates a connection diagram example: Figure 2-3 Typical Connection Diagram 3 Configuring Local Computer to Access the Wireless Router This chapter describes how to configure a computer for initial connection to the device. 3.1 Overview To access the Wireless Broadband Router’ s Web-based Configuration Utility, at least one properly configured PC must be connected to the device and reside on the same subnet with the Wireless Broadband Router. The easiest way to make the connection is attaching your host computer’ s network card directly to the LAN port of the device. Whatever your connection method is, the computer’ s Ethernet /wireless interface must be on the same subnet as the router. As the Wireless Broadband Router is configured with these default values: • IP address: 192.168.1.1 • Subnet mask: 255.255.255.0 • DHCP server: Enabled with the IP address...
Эта инструкция также подходит к моделям:Сетевое оборудование - RT210W (756.52 kb)
Сетевое оборудование - RT210W (756.52 kb)
Сетевое оборудование - RT210W (756.52 kb)
Сетевое оборудование - RT210W (756.52 kb)