Оценок - 2, средний балл: 4 ( )

Производитель: ADTRAN Размер: 2.09 mb Название файла: 5100-000334-000_Gateway_2700_IG_Rev_A.pdf Язык инструкции:

2. Use the network adapter configuration software or Windows network connection wizard to set the network name (SSID) and encryption key (WEP). a. The network name is the word “2WIRE” (in all capital letters), followed by the last three digits of the gateway serial number (for example, 2WIRE110). b. The encryption key is a 64-bit hex value, located beneath the bar code on the bottom of the 2Wire gateway. In the example, it is 4119627022. c. For Mac OS X users, you may need to enter the “$” character at the beginning of the encryption key (for example, $4119627022). Connect the First Computer to the Gateway USB Connection Note: The 2Wire 2070B gateway does not include USB support. If you are using a 2Wire 2070B gateway, skip this section. Figure 3. Gateway Connected Via USB 1. Connect the provided AC power adapter from the 2Wire gateway’s POWER port to an electrical outlet. The POWER light on the front of the gateway should be green. 2. Connect the provided blue USB cable from the gateway’s USB-PC port to the USB port on your computer. 3. Connect the provided gray telephone cable from the gateway’s PHONE LINE port to a telephone jack with DSL service. Connect the First Computer to the Gateway Install the 2Wire Gateway USB Driver - Windows 1. Power on your computer and place the 2Wire CD in your computer’s CD-ROM drive. 2. If the Add Hardware Wizard displays, follow the on-screen instructions. If prompted to identify where to search for drivers, deselect Floppy Disk drive and check CD-ROM drive. 3. After the driver installs click Finish to complete the driver installation. The Setup Wizard will resume when your PC has rebooted. Note: Microsoft Windows 98 users may be prompted to insert the Windows 98 installation CD-ROM after installing the 2Wire gateway USB drivers. After the Windows 98 updates are complete, remove the Windows 98 CD and reinsert the 2Wire CD into your CD-ROM prior to rebooting your PC. Install the 2Wire Gateway USB Driver - Macintosh Note: The 2Wire gateway supports USB for Macintosh OS 8.6, 9.2, 10.1.4, 10.1.5, 10.2.0, 10.2.1 to 10.2.6, 10.3.3 to 10.3.9, 10.4.0, and 10.4.1. Before making your USB connection to the gateway, you must install the 2Wire gateway USB driver on your computer. The following instructions are for USB installation on Macintosh computers running OS 10.2. 1. Power on your computer and place the 2Wire CD in your computer’s CD-ROM drive. 2. Double-click the 2Wire CD icon on your desktop. 3. Double-click 2Wire USB to begin the driver installation. 4. If you have set up an administrator name and password, the Authenticate screen opens. Enter your administrator name and password and click OK. 5. Follow the on-screen instructions. When the driver installation is complete, you will be prompted to restart your computer. 6. After your computer restarts, connect the provided blue USB cable from the USB-PC port on the 2Wire gateway to your computer’s USB port. Check Your Connections With your computer completely started, verify the POWER and USB-PC indicator lights on the front of the 2Wire gateway are green. If they are not, see “Understanding the Indicator Lights” on page 19. The INTERNET indicator light will not turn green until the gateway software has been installed and an Internet connection has been established. Run the 2Wire Setup Wizard Windows XP/2K/ME/98SE 1. Insert the 2Wire CD and follow the on-screen instructions. If the 2Wire Setup Wizard does not automatically start: . Double-click the My Computer icon located on the desktop. . Double-click the icon that corresponds to your CD-ROM drive. . Double-click Setup.exe and follow the on-screen instructions. 2. If prompted by the Setup Wizard, enter the 20-digit key code you received from your service provider. If you were not provided with a key code, contact your service provider. Macintosh OS 10.1.4/10.1.5/10.2.0 - 10.2.8/10.3.3 - 10.3.8 Note: MAC OS 9.X AND OTHER OPERATING SYSTEM USERS: Users running Mac OS 9.X and operating systems other than those stated above must perform a manual configuration of the gateway. Refer to “Appendix A: Install the Gateway on Other Operating Systems” on page 21 for step-by-step instructions. 1. Insert the 2Wire CD. 2. Double-click the 2Wire icon. 3. Double-click the 2Wire Setup Wizard icon. 4. If prompted by the Setup Wizard, enter the 20-digit key code you received from your service provider. If you were not provided with a key code, contact your service provider. Add Computers to the Network After your first computer is connected to the 2Wire gateway and your Internet connection has been established, you can connect other computers to the network. Use any of the following methods to connect additional computers to your network. Connection Type Page Ethernet page 12 USB page 13 Wireless page 14 Add Computers to the Network Ethernet Connection Figure 4. Gateway Connected to Second Computer Via Ethernet 1. Connect an Ethernet cable from any available ETHERNET1 port on the gateway to your ...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: