Оценок - 5, средний балл: 3.6 ( )

Производитель: Delta Размер: 975.97 kb Название файла: Язык инструкции:

B. Fig. A. Fig. B. 2 DRAIN OUTLET 1 3 4 REAR OF SINK DRAIN BODY 4 WHITE FOAM GASKET NOT VISIBLE DRAIN FLANGE 1 DOWN M965015 REV.1.7 Connect HOT water supply to inlet of left SHANK and COLD water supply to right SHANK using sealant, appropriate connectors, and COUPLING NUTS. Connect 1-1/4” O.D. tailpiece on POP-UP DRAIN to waste outlet. Thread TEE BODY (4) to SPOUT SHANK (5). Thread HOSE CONNECTOR (6, 6A) to VALVE CONNECTIONS (7, 7A). 9 Connect water supply to VALVE BODIES (1,1A) with 1/2" IPS FLEXIBLE SUPPLIES (2) or 3/8" O.D. BULL-NOSE RISERS (3). Use adjustable wrench to tighten connections. Do not over tighten. Be careful not to kink copper supply when bending. Use tubing cutter to cut to proper length. MAKE WATER SUPPLY AND WASTE CONNECTIONS NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS NOT INCLUDED AND MUST BE PURCHASED SEPARATELY. HOT COLD FERRULE COMPRESSION NUT COUPLING NUT FLEXIBLE SUPPLIES 1 1A 3/8 O.D. BULL-NOSE 1/2" PIPE THREAD RISERS 3/8 COMPRESSION CONNECTION 2 3 4 5 2 7 6 6A 7A Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes. Note: If STOPPER (2) does not open and close properly then refer to the “troubleshooting section” of these instructions. 8 CHECK OPERATION OF POP-UP 3 Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and hand tighten. Fig. A. Your new POP-UP DRAIN installation is now complete. Fig. B. Note: Tailpeice on pop-up drain is 1-1/4” O.D. Fig. B. Fig. A. 7 ATTACH CABLE CONNECTOR 2 1 Fig. B. 1-1/4” O.D. WASTE OUTLET 1 M965015 REV.1.7 10 INSTALL HANDLES CHECK DRAIN CONNECTIONS 11 12 13 14 TEST INSTALLED FITTING With HANDLES (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks. Remove AERATOR (3). Operate both HANDLES (1) to flush water lines thoroughly. Replace AERATOR (3). 1 HOT COLD 2 2 5 Operate POP-UP KNOB (5) and fill Sink with water. Check that DRAIN STOPPER (4) makes a good seal and retains water in Sink. If STOPPER (4) does not seal properly, please refer to “Troubleshooting Guide” in these instructions. Release POP-UP KNOB (5) down and check all drain connections and "P" trap for leaks. Tighten if necessary. 4 4 “P” TRAP WASTE OUTLET DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER.DRY WITH A SOFT COTTON FLANNEL CLOTH. DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A COARSE SURFACE. CARE INSTRUCTIONS: 1 2 4 5 3 BOTTOM SPLINE END UP Push ADAPTER (1) on VALVE STEM (2), so that the hole of the ADAPTER (1) with the spline is facing up. Fig. A. Tighten STEM SCREW (3) to secure ADAPTER (1). Find correct position of LEVER HANDLE ASSEMBLY (4) by adjusting male teeth on ADAPTER (1) to female teeth in HANDLE (4). Thread LEVER HANDLE ASSEMBLY (4) onto DECK ADAPTER (5) until snug against mounting surface. THREAD ON TO DECK ADAPTER Fig. A. 3 1 SERVICE (all models) 2 90° To change direction of handle rotation, proceed as follows: Turn valve to OFF position. Unthread HANDLE BASE (1) from DECK ADAPTE...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: