Оценок - 5, средний балл: 4
(
)
)
|
Фрагмент инструкции
Reassemble the operating rod as shown in Figure 12. Reinstall and adjust so that the foot valve is completely open when the foot lever is fully depressed. This prevents damage to the foot valve due to the absence of the override spring. 3. Turn supplies on and activate the sprayhead. Check piping installation for leaks. 4. Clean the sprayhead if necessary. See page 22 for sprayhead troubleshooting. Adjust the volume control valve, if necessary, to control the flow of water. Figure 12Figure 11 4/6/2007 Bradley Corporation • 215-603 Rev. M; EN 06-915B Classic Circular 36"/54" Washfountain with Foot Control Installation Instructions WF2605, WF2608 Terrazzo — WF2705, WF2708 Stainless Steel Soap Recommendations and Maintenance Tips Quality soap dispensers require good quality soap and periodic maintenance to properly operate. Bradley soap dispensers will provide dependable, consistent operation over the long term when soap with reasonable viscosity and pH levels are used and when a minimal amount of periodic maintenance is performed on the valves. Soap thickness is determined by a measurement called viscosity. Soap viscosity should be between 100 cps (centerpoise) and 2500 cps for all Bradley soap dispensers. Thinner soaps are perceived by the users as being “watered down” so users tend to take more than they need, resulting in waste. Thick soaps flow slower and inhibit the “flushing” action of the valves, which allows the soap to congeal in the valve and cause clogs. The pH (acid) level of the soap should be in the range of 6.5 to 8.5. More acidic soaps (pH levels lower than 6.5) will corrode metal parts (even stainless steel!!) and degrade rubber and plastic components. They will also cause skin irritation. Most inexpensive soaps (typically the pink lotion type) fall into this acidic category and will eventually cause valve failure and metal corrosion. Base soaps (pH levels higher than 8.5) will cause swelling or degradation of rubber and plastic parts and skin irritation. Generally, any quality soap meeting the viscosity and pH guidelines above will work well with Bradley soap dispensers. PCMX or Isapropanol based antibacterial soaps (within viscosity and pH limits) will also work with Bradley dispensers. Soaps satisfying these basic guidelines will provide consistent flow and reduce clogs. Most soap dispenser problems are caused by soap that is too thick or corrosive, or by a lack of maintenance. Many soaps come in concentrate form which must be diluted with water. Often, the soap is improperly diluted or used straight out of the bottle, which causes clogging and valve failure. If proper soap is being used, valves that have never been cleaned are usually the source of dispensing problems. Bradley has entered into an agreement with Champion Brand Products to provide additional customer service for purchasers of our dispensers regarding soap issues. They are very helpful and can get to the bottom of almost any soap dispenser-related problem. They also sell an excellent “Bradley approved” soap. Please see Bradley Instruction sheet 215-1286 for soap valve cleaning details and Champion Brand Products contact information. Check Valve Troubleshooting If water just dribbles or does not flow from sprayhead: 1. Turn off water supplies to fixture. 2 Inspect check valves for proper installation. See Stop, Strainer and Check Valve on page 19. 3. Open the stops and clean the strainers, if necessary. If water sprayhead delivers all hot or cold water: 1. Turn off water supplies to fixture. 2. Inspect check valves for proper installation. 3. Open the stops and clean the strainers, if necessary. 4. Inspect mixing valve for proper installation (see Vernatherm valve on page 24). Bradley Corporation • 215-603 Rev. M; EN 06-915B 4/6/2007 Item Part No. Description Attaching Parts S09-007S Qty 1 118-025 Valve Body 1 2 110-007 Packing Nut 1 3 135-001L Spring 1 4 125-001BU Washer 1 5 119-028 Plunger 1 * 161-014 Nut 1 * 124-001D Washer 2 * 142-002AH Washer - Stainless Steel 1 Classic Circular 36"/54" Washfountain with Foot Control WF2605, WF2608 Terrazzo — WF2705, WF2708 Stainless Steel Installation Instructions Soap Valve - Liquid - S09-007S Parts List * Not Illustrated This valve delivers a measured amount of soap with each upward stroke. The soap dispenser has been standard on washfountains since 1983 and is not well-suited for very thick lotion soaps. NOTE: Lotion soap will clog liquid soap valves. Use only lotion soap valves with lotion soap. Soap Valve - Lotion - S09-057S Parts List Item Part No. Description Valve Assembly S09-057 Attaching Parts S09-057S Qty 1 124-001D Washer — 1 2 110-057 Nut — 1 3 125-001AN Stopper — 1 4 159-114 Reinforcing Plate — 1 5 124-001AT Washer — 1 6 160-176 Screw — 1 7 S09-040 Valve 1 1 8 S53-045 Adaptor 1 1 Soap Valve - Powdered - S09-010A Parts List Item Part No. Qty Description 1 160-069 1 Screw, 1/4-20 RD 2 142-002X 1 Washer, 1/4 Split-Lock 3 S62-002 1 Agitator / Slide Assy. 4 192-004 1 Lever - P...
Эта инструкция также подходит к моделям:Сантехника - WF2708 (416.5 kb)