Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
FRAME (4) 3/8" BOLT AND WASHER Figure 4 Figure 2 1-1/2" NPT DRAIN STUB-OUT 1/2" NPT HOT AND COLD SUPPLIES OR TEMPERED SUPPLY STUB-OUTS Figure 3 PANEL FRAME (8) TORX-HEAD SCREW SCUFF PANEL (do not remove) SCUFF PANEL (do not remove) Installation Instructions continue . . . Bradley Corporation • 215-1244 Rev. D; EN 08-805 4/24/08 Express® Lavatory System SS-Series SS-2/AST/STD, SS-2/AST/JUV Installation - Obsolete Installation Instructions continued . . . Step 3: Installing bowl assembly IMPORTANT: Moving and positioning the bowl will require more than one person. Note: Refer to Figure 5 below when installing the bowl assembly. 1. With someone to assist you, place the bowl assembly squarely onto the frame. 2. Attach the front of the bowl assembly to the frame using the two 1/4"-20 x 3/8" pan-head screws and washers. Do not tighten screws at this time. IMPORTANT: When bolting the bowl assembly to the frame and wall, do not overtighten bolts. Overtightening bolts can damage the Terreon® material. 3. After the bowl assembly is attached to the frame, use two 3/8" bolts and washers (supplied by the installer) to bolt the bowl to the wall anchors. 4. Tighten the screws installed in procedure #2 above to secure the bowl assembly to the frame. Do not overtighten. BACK VIEW 3/8" BOLT AND WASHER BOWL ASSEMBLY 3/8" BOLT AND WASHER 1/4"-20 X 3/8" PAN HEAD SCREWS AND Figure 5 WASHERS Installation Instructions continue . . . 4/24/08 Bradley Corporation • 215-1244 Rev. D; EN 08-805 Express® Lavatory System SS-Series Installation - Obsolete SS-2/AST/STD, SS-2/AST/JUV Installation Instructions continued . . . Step 4: Connecting supply and drain 1. FOR HOT AND COLD SUPPLY: Connect the flexible hoses installed to the Vernatherm™ Mixing Valve to the hot and cold water supply piping from the wall (see Figure 6a). Note: The red marking on Vernatherm™ Mixing Valve indicates hot water supply inlet. FOR SINGLE TEMPERED SUPPLY: Attach the stop/strainer/check valve to the 1/2" tempered supply line. Connect the flexible hose to the stop/strainer/check valve and air valve manifold (see Figure 6b). 2. Install the drain plug in the hole in the bottom of the bowl (see Figure 7). 3. Beneath the bowl, install the 1/4" rubber washer onto the drain plug, and thread the tailpiece to the drain plug. 4. Assemble the P-trap by connecting the 1-1/2" tubular pipe to the tailpiece and to the 1-1/2" drain pipe stubbed out of the wall. 5. Install the strainer on the drain plug opening inside the bowl, and push the strainer firmly into place. Secure the strainer to the drain with the screw provideed. Figure 6a VERNATHERM™ THERMOSTATIC MIXING VALVE FLEXIBLE SUPPLY HOSE FLEXIBLE SUPPLY HOSE CONNECT TO 1/2" NPT HOT CONNECT TO 1/2" NPT COLD WATER SUPPLY WATER SUPPLY Figure 7Figure 6b FLEXIBLE SUPPLY HOSE CONNECT TO TEMPERED WATER SUPPLY Bradley Corporation • 215-1244 Rev. D; EN 08-805 4/24/08 Express® Lavatory System SS-Series SS-2/AST/STD, SS-2/AST/JUV Installation - Obsolete Installation Instructions continued . . . Step 5: Connecting plastic tubing NOTE: Refer to Figure 8a for hot and cold supplies, and refer to Figure 8b for tempered supply. 1. Connect the plastic tubing for the water supplies from the sprayhead assembly to the quick- connect fittings on the air valve as follows: • insert the tubing with the red marking to the left valve • insert the tubing with the green marking to the right valve IMPORTANT: The plastic tubing for the water supplies and pushbuttons are pre-cut to the correct lengths. If the tubing is cut too short, kinking can occur and cause leaks at the fitting locations. 2. Connect the plastic tubing for the pushbuttons from the sprayhead assembly to the quick-connect fittings on the air valve as follows: • insert the tubing with the red marking to the left valve • insert the tubing with the green marking to the right valve 3. Assemble the P-trap (supplied) and make drain connections. AIR TUBING (RED) WATER SUPPLY (RED) AIR VALVE Figure 8a AIR TUBING (GREEN) WATER SUPPLY (GREEN) FLEXIBLE SUPPLY HOSE VERNATHERM™ MIXING VALVE Figure 8b AIR VALVE WATER SUPPLY (GREEN) AIR TUBING (GREEN) WATER SUPPLY (RED) AIR TUBING (RED) FLEXIBLE SUPPLY HOSE 4/24/08 Bradley Corporation • 215-1244 Rev. D; EN 08-805 Express® Lavatory System SS-Series Installation - Obsolete SS-2/AST/STD, SS-2/AST/JUV Installation Instructions continued . . . Step 5: Completing installation 1. Turn on the water supply to the Express® and check for leaks. 2. Install the panel to the frame. Fasten panel with the eight Torx-head screws provided (see Figure 9 below). Figure 9 FRAME (8) TORX-HEAD SCREW PANEL Bradley Corporation • 215-1244 Rev. D; EN 08-805 4/24/08 11 Express® Lavatory System SS-Series SS-2/AST/STD, SS-2/AST/JUV Installation - Obsolete Cleaning and Maintenance Instructions IMPORTANT: Strong alkaline or acid-based chemicals and cleansers should not beused to clean Terreon®. If these chemicals come in contact with the Terreon® surface, wipe off the surface immedia...
Эта инструкция также подходит к моделям:Сантехника - EXPRESS SS-2/AST/JUV (198.5 kb)