Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
Cutting the cord or plug will void the warranty and make the pump inoperable. Figure 4 - Typical Installation Three prong grounded outlet equipped with a ground fault interruptor Main waste line to sewer or septic tank 2 in. Discharge pipe Upper level drainage Cleanout Pump Float Switch Flange Floor drain Dryer Washer Laundry tubs Vent pipe Lavatory Shower Washer drain 45° Elbow 2 in. Check valve 2 in. gate valve Operating Instructions and Parts Manual Union Operating Instructions and Parts Manual Operation (Continued) 2. With the cover removed, add water to the basin and observe the float control switch operation. 3. Also, test alarm switch if installed. 4. Secure and seal basin cover. Do not run your pump in a dry sump. Do not attempt to oil the motor. A special oil has been put in the motor housing at the factory. Use of any other oil could damage the pump and WILL void the warranty. High Water Level Low Water Level Figure 5 - Simplex System Maintenance Always disconnect the electrical supply before attempting to install, service, relocate or perform any maintenance. If the power source is out of sight, lock and tag in the open (off) position to prevent unexpected power application. Failure to do so could result in fatal electrical shock. Only qualifi ed electricians should repair this unit. Improper repair could result in fatal electrical shock. 1. Let the pump cool for a minimum of two hours before servicing because the pump contains hot oil under pressure and the motor is hot. 2. Disassembly of the motor prior to expiration of warranty will void the warranty. If repairs are required, see troubleshooting chart. 3. Inlet should be kept clean and free of all foreign objects and inspect annually. A clogged inlet will damage pump. 4. Pump should be checked monthly for proper operation. This pump contains dielectric oil for cooling. This oil can be harmful to the environment. Check the state environmental laws before disposing this oil. Figure 6 - Duplex System Off Level On Level Alarm Level Pump #1 Discharge Pump #2 Discharge 4 Operating Instructions and Parts Manual Troubleshooting Chart Symptom Possible Cause(s) Corrective Action Pump will not start or run 1. Blown fuse, tripped breaker 1. If blown, replace with proper sized fuse or reset breaker 2. Low line voltage 2. If voltage is under 108 volts, check wiring size 3. Defective motor 3. Replace pump 4. Defective float switch 4. Replace float switch 5. Stuck/ jammed impeller 5. If impeller will not turn, remove housing and remove blockage 6. Float obstructed 6. Make sure float(s) move freely up and down Pump starts and stops too 1. Back-flow of water from 1. Install or replace check valve often piping 2. Faulty float switch 2. Replace float switch Pump will not shut off or 1. Defective float switch 1. Replace float switch thermal protector turns off 2. Obstacle in piping 2. Remove pump and clean pump and piping 3. Float obstructed 3. Make sure float move freely up and down 4. Low line voltage 4. If voltage is under 108 volts, check wiring size 5. Too many appliances on 5. Install pump on dedicated circuit. IMPORTANT: Do not circuit use extension cord to power pump. Pump operates but delivers 1. Plugged impeller 1. Clean out impeller little or no water 2. Check valve installed 2. Reverse position of check valve backwards 3. Pump air locked 3. Check the 1/8 in. hole in discharge line between pump and check valve; it should be 1 in. to 2 in. above discharge flange and before the check valve 5 6 For Replacement Parts or Technical Assistance, Call 1-800-237-0987 Please provide following information: Address any correspondence to: - Model number Wayne Water Systems - Serial number (if any) 101 Production Drive - Part description and number as shown in parts list Harris...
Эта инструкция также подходит к моделям:Сантехника - 332200-001 (834.72 kb)
Сантехника - SEP4 (834.72 kb)
Сантехника - SEP5 (834.72 kb)
Сантехника - SEP8 (834.72 kb)