Оценок - 4, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
10A a. Adjust water level. Water level should be adjusted to level indicated on tank by adjusting float cup. 1" ABOVE OVERFLOW PIPE FLOAT CUP "S" CLIP See Step 11 for water level adjustment method FILL VALVE FLUSH VALVE b. If bowl fails to siphon, an adjustment may be required with the lift chain. VALVE BODY WATER LEVEL ADJUSTMENT ROD Simply remove the bead chain from the retainment clip (see Fig. 10A) and take up slack on the chain, andADJUSTABLE HEIGHT FLAPPER SHANK WASHER reinsert on lift rod. Make sure the chain is not too taught. Turn on water supply. Submerge the FLOAT CUP LOCK NUT CONE WASHER THREADED SHANK seconds. Adjust the water to desired level by turning under the water for 30 WATER LEVEL ADJUSTMENT COUPLING NUT (HAND TIGHT ONLY) CARE AND CLEANING PARTS FOR WATER CONNECTION (SEE STEP 9) Diagram 1 ROD and moving FLOAT CUP up or down. 12 When cleaning your toilet, wash it with mild, soapy water, rinse thoroughly with clear water and dry with a soft cloth. Avoid detergents, disinfectants, or cleaning products in aerosol cans. NEVER use abrasive scouring powders or abrasive pads on your toilet seat. Some bathroom chemicals and cosmetics may damage the seat's finish. ! WARNING: Do not use in-tank cleaners. Products containing chlorine (calcium hypochlorite) can seriously damage fittings in the tank. This damage can cause leakage and property damage. American Standard shall not be responsible or liable for any tank fitting damage caused by the use of cleaners containing chlorine (calcium hypochlorite). 4037 REPAIR PARTS LIST TANK NUMBER Repair parts are determined by toilet tank number which can be found marked inside tank. 4392 NOTE: "XXX" represents color or trim finish options. Specify when ordering. 4037W/LINER PART NO. DESCRIPTION 4392 W/LINER 735076-400-XXX 4037 TANK COVER 735098-400-XXX 4392 TANK COVER 738565-433.0070A FLUIDMASTER 400A VALVE 738570-1030A FLUIDMASTER REFILL TUBE 7381009-0070A FLUIDMASTER REFILL CLIP 7381007-402.0070A FLUIDMASTER FLUSHVALVE 7381007-404.0070A FLUIDMASTER FLUSHVALVE 730512-0070A TANK COUPLING KIT #232 7381024-400.0070A FLUIDMASTER FLAPPER ASSEMBLY 7381024-402.0070A FLUIDMASTER FLAPPER ASSEMBLY 047192-XXX0A TRIP LEVER ASSEMBLY LH 034783-XXX0A BOLT CAP KIT #128 5329.XXX SEAT 7301186-100 Rev. C - 3 INSTRUCTIONS TO INSTALL TOILET SEAT 12a Place seat on bowl. Be careful to center hinge over holes in bowl. 12b Insert bolts in hinges. 12cAttach the nut from below. 12d 12e 12f TOILET SEAT CARE AND CLEANING When cleaning your toilet seat wash it with mild, soapy water: rinse the seat thoroughly with clear water: and dry with a soft cloth. Avoid detergents, disinfectants, or cleaning products in aerosol cans. NEVER use abrasive scouring powders on your seat. Some bathroom chemicals and cosmetics may damage the seat's finish. After installation, check Use a screwdriver to tighten bolt. Close the hinge covers. the tightness of the bolts from time to time to ensure a tight fit. 13 • Make sure water supply is off. Remove valve TOP by lifting arm and rotating top and arm 1/8 turn counterclockwise, pressing down slightly on cap. IMPORTANT: Always clear sand and rust from system. • While holding a container over the uncapped VALVE to prevent splashing, turn water supply on and off a few times. Leave water supply off. • Replace TOP by engaging lugs and rotating 1/8 turn clockwise. MAKE CERTAIN TIP IS TURNED TO THE LOCKED POSITION. VALVE MAY NOT TURN ON IF TOP IS NOT FULLY TURNED TO THE LOCKED POSITION. For troubleshooting information please contact: TROUBLESHOOTING IF FILL VALVE SHUTS OFF BUT CONTINUES TO LEAK SLOWLY, repeat Step 13. IF FILL VALVE TURNS OFF AND ON DURING PERIODS OF NON-USE, it is a signal you are wasting water because: • The end of the refill tube is inserted into overflow pipe, below water level in tank. Attach refill tube to overflow pipe using "S" clip provided. • The flush valve is leaking because it's worn, dirty or misaligned with tank ball or flapper (replace with a new flapper). IF FILL VALVE WON'T TURN ON OR SHUT OFF or REFILL OF TANK WATER IS SLOW after valve has been in use for some time, Fluidmaster Model 242 Replacement Seal may be needed. Go to our website at for more solutions to toilet problems. © 2001 Fluidmaster, Inc. ® Registered trademark of Fluidmaster, Inc. GUARANTEE: This Fluidmaster product is guaranteed to be free from defective materials and workmanship for a period of one year. Units returned to Fluidmaster will be replaced without charge. Always use quality Fluidmaster repair parts when maintaining your Fluidmaster products. Fluidmaster shall not be responsible or liable for any damages caused by products used with Fluidmaster valves that were not manufactured by Fluidmaster, Inc. 30800 Rancho Viejo Road San Juan Capistrano, CA 92675 (949) 728-2000 (800) 631-2011 LIFT ARM FIRST NOTE: Pictures are representative and may notexactly depict the flush valve. 7301186-100 Rev. C - 4 TROUBLESHOOTING GUIDE ...