Оценок - 3, средний балл: 4.7
(
)
)
|
Фрагмент инструкции
This warranty shall be void if the product has been moved from its initial place of installation; if it has been subjected to faulty accident or other damage; if it was not installed in Standard's instructions; or if it has been modified in a product as shipped by American Standard. American Standard's option to repair or exchange the product warranty does not cover any labor or other costs of removal nor shall American Standard be responsible for any other incidental consequential damages attributable to a product defect or to exchange of a defective product, all of which are expressly excluded this warranty. (Some states or provinces do not allow the exclusion or limitation of implied warranties, so this exclusion may not apply to you.) This warranty gives you specific legal rights. You may have other statutory rights that vary from state to state or from province to province, in which case warranty does not affect such statutory rights. For service under this warranty, it is suggested that a claim be made through the contractor or dealer from or through whom the product was purchased, or that a service request (including a description of the product model and of the defect) be sent to the following address: In the United States: AMERICAN STANDARD, INC. P.O. Box 6820 Piscataway, New Jersey 08855 Attn: Director of Consumer Affairs For residents of the United States, warranty information may also be obtained by calling the following toll free number: (800) 223-0068 In Canada: AMERICAN STANDARD, INC. 2480 Stanfield Road Mississauga, Ontario Canada L4Y 1S2 Toll Free: (800) 387-0369 Toronto Area: (905) 276-6022 In Mexico: IDEAL STANDARD, S.A. de C. V Customer Service Manager Planta Santa Clara,Via Morelos #330 Santa Clara Coatitla Ecatepec de Morelos 55540, Estado de Mexico, Mexico © American Standard Inc. 2002 730523-100 by COLLECTION™ “ ” THE Observe Local and Building Model 0283 Series Pedestal Lavatory Installation Instructions Introduction: Thank you for selecting our products...have been the benchmarks of fine To help insure that the installation process will proceed carefully before you begin. Also, review the recommended tools and materials list; carefully unpack and examine Recommended Tools & Materials 1 Provide suitable reinforcement behind finished wall for lavatory anchor screws. * Determine horizontal center line location of support from fixture. Adjustable Wrench Channel Locks Regular Screwdriver Phillips Screwdriver 10' Pipe Wrench Putty Kinfe Drill Saber Saw Level Basin Wrench Plumbers' Putty or Caulking Tubing Cutter Tape Measure Hacksaw Anchor Screw LocationC/L of 2X6 Support Finished Floor Pedestal Location NOTE: If replacing an existing lavatory be certain to shut off water supply before removing old lavatory. * 2 Install lavatory anchor screws leaving 1-7/8" threaded end exposed as illustrated. Following manufacturer's instructions, install faucet and drain assembly (not included). Be certain to apply a bead of sealing putty on the underside of the drain (area "A") in order to ensure a watertight seal between the lavatory and drain. Remove excess putty after installing drain on lavatory. 6 Secure lavatory to wall as shown in Step 4. Install washers and hand tighten nuts or lag bolts. Level and square the unit. Connect hot and cold supply lines to the shut-off valves. Tighten trap joints for watertight assembly. 7 Install pedestal screw. Securely tighten lavatory anchor nuts. alignment. It may be necessary to cut off part of the tailpiece (area "B") and/or part of the drain elbow of the trap (area "C"). 3 4 5 1-7/8" B C Rear View Pedestal Screw Return the fitted and pedestal installed position. Connect trap to drain assembly hand tight to check A ANCHOR SCREW INSTALLATION Anchor Screw Washer Lavatory NutIMPORTANT: Final assembly of nut and washer method shown for reference only. (See steps 7 and 8). Place lavatory square the lavatory pedestal screw locations 8 Note: Space constraints may dictate method of fastening pedestal to floor. Remove lavatory and pedestal installed position. Drill pilot holes for lavatory and pedestal anchor screws. Use the kit provided for lavatory and pedestal installation. Shut-off Valves 2 Install lavatory anchor screws leaving 1-7/8" threaded end exposed as illustrated. Following manufacturer's instructions, install faucet and drain assembly (not included). Be certain to apply a bead of sealing putty on the underside of the drain (area "A") in order to ensure a watertight seal between the lavatory and drain. Remove excess putty after installing drain on lavatory. 6 Secure lavatory to wall as shown in Step 4. Install washers and hand tighten nuts or lag bolts. Level and square the unit. Connect hot and cold supply lines to the shut-off valves. Tighten trap joints for watertight assembly. 7 Install pedestal screw. Securely tighten lavatory anchor nuts. alignment. It may be necessary to cut off part of the tailpiece (area "B") and/or part of the drain elbow of the...