Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
Tighten if necessary. 1 1 4 SPRAY OUTLINE OF BIDET 2 2 3 UNTHREAD INSTALL HANDLES 1 2 4 5 3 TOP Figure "A" SPLINE END DOWN Push ADAPTER (1) on VALVE STEM (2), so that the hole of the ADAPTER (1) without a spline is facing up. See figure "A". Tighten STEM SCREW (3) to secure ADAPTER (1). Find correct position of LEVER HANDLE ASSEMBLY (4) by adjusting male teeth on ADAPTER (1) to female teeth in HANDLE (4). Thread LEVER HANDLE ASSEMBLY (4) onto ESCUTCHEON (5) until snug against mounting surface. THREAD ON TO DECK ADAPTER To change direction of handle rotation, proceed as follows: Turn valve to OFF position. Thread counter-clock wise HANDLE BASE (1) to remove HANDLE ASSEMBLY (2) from ESCUTCHEON BASE (3). Use a flat blade screw driver to remove SPRING CLIP (4). Lift STOP WASHER (5), turn 90° and replace. Replace SPRING CLIP (4). Reinstall HANDLE ASSEMBLY (2). If spout drips, operate handles several times from OFF to ON position. Do not force - handles turn only 90°. 90° VALVE 1 5 3 4 2 DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH. DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A COARSE SURFACE. CARE INSTRUCTIONS: M968924 Rev.1.3 Speed Connect™ Drain Troubleshooting Guide Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A. Look at the area on the Drain Body where the Cable was attached and locate the component labeled as “Cam” and “Cam Cap” in the illustration. Fig. B. Use fingers or small screwdriver under either side of the Cam Cap to pry it out from the Drain. Fig. D. Remove the Cam by pulling it straight out while wiggling gently to loosen the Rubber Seal. Fig. E. The Stopper can now be removed by lifting it out of the Drain. Fig. F. CAM CAM CAP CABLE ADJUSTMENT PROCEDURE If sink does not hold water even though Stopper is in the “down” position: • Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly: • Follow CABLE ADJUSTMENT PROCEDURE. If you need to remove the Stopper: • Follow STOPPER REMOVAL PROCEDURE. If you would like the ability to remove your Stopper simply by lifting it out of the drain: • Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode. Fig. B. REMOVE CAM Fig. E. Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A. Look at the area on the Drain Body where the Cable was attached and locate the component labeled as “Cam” in the illustration. Fig. B. Use a small screwdriver to rotate the Cam in the clockwise direction as far as it will go. At this point the Stopper should be in the UP position. Fig. B, C. Push DOWN on the Lift-Knob to make sure it is fully down. Fig. C. Re-attach the Cable to the Drain Body Connection (2) by threading the Cable Connector (1) clockwise onto the Drain Body Connection (2) and hand-tighten. Fig. A. STOPPER REMOVAL PROCEDURE 2 1 1 RE-ATTACH DISCONNECT Fig. D. REMOVE CAM CAP Fig. C. STOPPER Fig. F. Fig. A. DOWN STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be removed) or “Unlock” Mode (Stopper is removable). Locked Mode: Look ...
Эта инструкция также подходит к моделям:Сантехника - SERIN 2064.4 (698.39 kb)
Сантехника - SERIN 2064.4 (698.39 kb)
Сантехника - SERIN 2064.4 (698.39 kb)