Оценок - 3, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
. If the air dryer function selection button is pressed while in cleansing operation, the cleansing function is stopped and drying starts immediately. . Stop If you want to stop the operation in use, press stop button. - It stops all operating functions. . The air dryer function is stopped in 2 seconds after the stop button is pressed. 17 How To Use HOW TO USE | For Rear Cleansing | For Front Cleansing For Front Cleansing . Front cleansing Sit on the seat and press the front cleansing function selection button on the remote control. - The cleansing water is ejected for about 1 minute and then automatically stopped. - An automatic nozzle cleaning is performed for about 5 seconds after cleansing when the nozzle retracts itself. . Adjust the nozzle position by pressing the nozzle position button. . If the front cleansing function selection button is pressed again while in cleansing operation, additional front cleansing starts again for another 1 minute. . While in cleansing, users can adjust the water temperature, water pressure, and nozzle position according to their preference. . Move Press the move function selection button on the control panel. - The nozzle moves back and forth, providing a wider range of cleansing. . It will be worked continuously while the cleansing function is operated. . You can adjust the nozzle position by pressing the nozzle position button. . To stop the move function, press the move function selection button again. . Air dryer Press the air dryer function selection button on the remote control. - Warm air blows for about 2 minutes to dry the wet part. . If you wipe out the wet before turning on the air dryer function, you can finish drying faster. . You can adjust the air dryer temperature by pressing the water pressure air dryer buttons. . If the air dryer function selection button is pressed again while in drying operation, additional drying starts again for another 2 minutes. . If the air dryer function selection button is pressed while in cleansing operation, the cleansing function is stopped and drying starts immediately. . Stop If you want to stop the operation in use, press stop button. - It stops all operating functions. . The air dryer function is stopped in 2 seconds after pressing the stop button. 18 INSTALLATION . Installing the product Tighten the fixing screws firmly so that the bidet body won’t be shaky on the toilet. . Product installation place As the bidet is installed on the toilet, please install not to have water splashed on the bidet. . After installation Keep the removed existing toilet seat in a shaded place to prevent its damage. . Cold water pipe Make sure to connect the bidet to cold water pipe (If the product is connected to warm water pipe, the filter and hoses of the bidet may be damaged). . To maintain the optimal product performance, consult a Coway engineer for detailed installation methods. . There may be some water remaining inside the filter which was used to test the product during the inspection process at the factory. - The remaining water does not mean that the product was previously used. Tips TipsKeep the existing toilet seat in the shaded place Warm water 19 Maintenance INSTALLATION | Uninstallation Existing Toilet Seat | Installation the Product Uninstallation Existing Toilet Seat 1. Remove the fixing nuts of the existing seat and separate the existing toilet seat 1 and the seat cover 2 . . Keep the removed seat and seat cover in a shaded place. Installation the Product 1. Turn off the main water supply valve 1 and separate the existing water tank hose 2 . 2. Connect the rubber packing, T-shaped connector, and water tank hose in order to the existing tap water pipe. . Please connect the bidet hose to the T-shaped connector. . Please insert the rubber packing between the water pipe and the T-shaped connectior necessarily. Firmly rotate the nuts below and on top of the T-shaped connector to the end clockwise. 3. Please connect MF filter to the product body. . Please assemble by rotating the MF filter on the filter holder in the lower left side of the bidet body. If the MF filter is assembled completely, as the bidet may not function normally, please be careful. 4. Put the fixing plate and the fixing slider on the bidet as the figure. Insert the fixing screw to the filter holder, push the fixing rubber and the fixing washer, and tighten the fixing nuts. Tighten the fixing screws firmly so that the bidet body won’t be shaky on the toilet. Users may fall off the seat and get injured. .. .. .. .. 20 INSTALLATION Installation the Product 5. Please install by adjusting the rear of the body to the fixing plates and pushing the product back. 6. Connect the T-shaped connector and the connected bidet hose to the bidet body. . Please shorten the bidet hose as soon as possible. If the bidet hose is long, it may cause noises. 7. Open the main water supply valve. 8. Connect the power plug to the electrical outlet. . Make sure to use a grounded electrica...
Эта инструкция также подходит к моделям:Сантехника - BA07-E (14.28 mb)