Войти:
Оценок - 3, средний балл: 3.7 ( )

Инструкция по эксплуатации Delta, модель 16968-DST Series

Производитель: Delta
Размер: 1.87 mb
Название файла: 5caf2050-8152-4bb0-a3eb-e43f6777d89e.pdf
Язык инструкции:enesfr
Перейти к скачиванию



Фрагмент инструкции


Place gasket (1) into groove on bottom of base ring (2). Place base ring onto sink over mounting hole, then install trim ring (3) over base ring. Tabs (4) on trim ring and base ring should be aligned together at the front and rear of the installation hole. Insert faucet lines and shank through mounting hole, then install hub (5) onto trim ring. Ensure that tabs on trim and base rings are correctly located in slots on bottom of hub. A. 5 1 3 2 4 1 2 3 4 4 4 4 2Faucet Installation 3 A. Push hose partially up into mounting shank (1). Install the mounting bracket (2) and nut (3) onto mounting shank (1) using wrench (4). For decks up to 1 3/8" (35 mm) thick, use provided spacer (5) between nut and mounting bracket. Note: The wrench provided is designed to be used with a variety of tools: flat/Phillips head screwdrivers, wrenches, etc. HINT: Turn the spout tube opposite the handle to balance the assembly and aid the hose installation when mounting. B. 3 4 B. 2 5 1 Your faucet is designed for a hole diameter of 1 3/8" ± 1/8" (35 mm ± 3 mm) and a deck thickness up to 2 1/2" (64 mm). Place gasket (1) into groove on bottom of base ring (2). Place base ring onto sink over mounting hole, then install trim ring (3) over base ring. Tabs (4) on trim ring and base ring should be aligned together at the front and rear of the installation hole. Insert faucet lines and shank through mounting hole, then install hub (5) onto trim ring. Ensure that tabs on trim and base rings are correctly located in slots on bottom of hub. A. 5 1 3 2 4 1 2 3 4 4 4 4 4 1 2 3 2 4 OPTIONAL A. OPTIONAL B. 2 3 1 5 1 2 3 2 4 OPTIONAL A. OPTIONAL B. 2 3 1 5 Faucet Installation with 10" Escutcheon A. For optional installations using the 10" B. Push hose partially up into mounting escutcheon, replace the trim ring with shank (1). Mount as shown above using the escutcheon (1), undercover plate (2) the nuts (2), bracket (3) with nut and and gasket (3). wrench (4) and spacer (5) (if needed). Note: The wrench provided is designed to be used with a variety of tools: flat/Phillips head screwdrivers, wrenches, etc. 5 32 1 3 32 1 3 6 5 4 5 4 Hose Installation Remove hose guide (1). Slide hose weight (4) onto faucet outlet (5). Attach clip (6) over (2) over end of hose (3). Push hose end hoses as shown. 6 Ensure all fittings and end connections are free of debris. Faucet fittings (1) are 3/8" compression, with ends colored red for hot and blue for cold. Loop tubing (2) if it is too long. Note: Recommended tubing minimum bend diameter is 8". Secure metal nut (3) on faucet tube to supply valve Water Line Connections 1 3 4 4A2 2 connection (4) and hand tighten, then tighten one additional turn with wrench. DO NOT OVERTIGHTEN. Repeat for other tube. WARNING: Do not use pipe dope or other sealants on water line connections. 3 Ensure all fittings and end connections are free of debris. Faucet fittings (1) are 3/8" compression, with ends colored red for hot and blue for cold. Loop tubing (2) if it is too long. Note: Recommended tubing minimum bend diameter is 8". Secure metal nut (3) on faucet tube to supply valve Water Line Connections 1 3 4 4A2 2 connection (4) and hand tighten, then tighten one additional turn with wrench. DO NOT OVERTIGHTEN. Repeat for other tube. WARNING: Do not use pipe dope or other sealants on water line connections. 3 7 4BCustom Fit Connections NOTICE: If you determine the PEX supply tubing for this faucet is too long and must be shorter to create an acceptable installation, be sure to read the instructions and plan ahead.When cutting the supply tubing the installer accepts the responsibility to do so in a way that allows a leak-free joint to be created. Delta is not responsible for tubing that is cut too short or cut in a way that will not allow for a leak-free joint. For custom fit installations, you must use RP50952 sleeves supplied with model and nuts included on supply lines. Tube cut must be straight. See plastic sleeve installation instructions found in RP50952 and included in this document (page 9) for more information. Secure metal nut (1) on faucet tube to supply valve connection (2) and hand tighten, then tighten an additional 2 turns with wrench. DO NOT OVERTIGHTEN. Repeat for other tube. WARNING: Do not use pipe dope or other sealants on water line connections. Potential Problems and Remedies lTubing is not cut perpendicular to the axis of the tub: carefully make an additional cut, being careful not to cut the tube too short. lTubing is cut too short: buy a coupling union and a replacement supply line that mate together from a store. The coupling union end intended to connect to the faucet must mate to the standard 3/8" connection nuts and plastic sleeves supplied with the faucet. lThe plastic sleeve or connection nut is lost: purchase a replacement nut and/or plastic sleeve that are designed to seal with PEX tubing. NOTICE: DO NOT use a metal sleeve, RP51243 gasket (supplied with faucet) or ferrule in the place of the plastic sle...


Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории