Оценок - 2, средний балл: 3
(
)
)
|
Фрагмент инструкции
(54mm) 2" MAX. (51mm) MAX. 1-1/4" O.D. (32mm) O.D. Pipe Wrench Teflon Tape Plumbers' Putty or Caulking Tubing Cutter WALL MOUNT FAUCET IN-WALL LAVATORY FITTING SERIN™ To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin. Thank you for selecting American-Standard... the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly-- please read these instructions carefully before you begin. M968852 Rev.1.3 4 3 INSTALL HANDLES GROOVE GROOVE FINISHED WALL 1 1 4 8 9 5 6 7 4 2 DRAIN INSTALLATION Assembly GASKET (2) WASHER (3) and LOCKNUT (4) onto DRAIN BODY (1). Tighten LOCKNUT (4) firmly. Assembly TAILPIECE (5) to DRAIN BODY (1). Apply a bead of PUTTY to underside of FLANGE on DRAIN BODY (1). Feed DRAIN BODY (1) down through lavatory. LAVATORY PUTTY 2 3 4 5 1 2 INSTALL WALL SPOUT Remove PLASTER GUARDS (1) from valve bodies. Inspect that SPOUT NIPPLE O-RING (2) is seated in groove of SPOUT NIPPLE (3). Thread SPOUT MOUNT (4) onto SPOUT NIPPLE (3). Align groove on SPOUT MOUNT (4) with face of finished wall. See Figure A. Install SEAL (5) into SPOUT ESCUTCHEON (6). Place SPOUT ESCUTCHEON (6) with SEAL (5) onto SPOUT MOUNT (4). Push SPOUT (7) onto SPOUT MOUNT (4). Align SPOUT (7) and tighten SPOUT SET SCREW (8) with 3mm HEX WRENCH (9) supplied. Figure A 1 MAXWAL MIN1-5/8"DE MAXWALL MIN1-5/8"DEEP 3 1 5 2 3 4 Thread HANDLE BASE (4) onto HANDLE ESCUTCHEON (3) until seated tightly against HANDLE ESCUTCHEON (3). Place O-RING (2) into HANDLE ESCUTCHEON (3). Thread HANDLE ESCUTCHEON (4) onto VALVE (5) until snug against finished wall. Turn VALVE STEMS (1) to off position. 5 SERVICE 3 To change direction of handle rotation, 4 proceed as follows: Turn valve to OFF position. Thread counter-clock wise HANDLE BASE (1) to remove HANDLE ASSEMBLY (2) from ESCUTCHEON BASE (3). Use a flat blade screw driver to remove SPRING CLIP (4). Lift STOP WASHER (5), turn 90° and replace. Replace SPRING CLIP (4). Reinstall HANDLE ASSEMBLY (2). If spout drips, operate handles several times from OFF to ON position. Do not force - handles turn only 90°. TO REMOVE HANDLE 90° 2 5 1 6 TEST INSTALLED FAUCET Turn HANDLES to "off" position. Remove AERATOR (1) using TOOL (2) supplied. Turn hot and cold water supplies on. Operate both HANDLES to flush water lines thoroughly. Check spout connections for leaks. Check all drain connections for leaks. Turn handles to OFF position. Replace AERATOR (1). 1 2 CARE INSTRUCTIONS: DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH. DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A COARSE SURFACE. M968852 Rev.1.3 SERIN™ WALL MOUNT LAVATORY FAUCET MODEL NUMBER 2064.451 M950245-YYY0A HANDLE ASSEMBLY M962424-YYY0A HANDLE ESCUTCHEON KIT M962422-YYY0A SPOUT ASSEMBLY M962423-YYY0A SPOUT ESCUTCHEON KIT 918555-0070A HANDLE SCREW 617852-0070A ADAPTER M962352-0070A SPOUT MOUNTING KIT 9...
Эта инструкция также подходит к моделям:Сантехника - SERIN M968852 (219.1 kb)
Сантехника - SERIN M968852 (219.1 kb)
Сантехника - SERIN M968852 (219.1 kb)