Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
6 1/4” - 8” under normal conditions. The detection area may be less for dark, non-reflective objects, or greater for bright, highly reflective objects. • If the sink is very small or highly reflective, follow the range reduction instructions on page 12. When the faucet is in reduced range mode, the LED in the sensor window will flash while the faucet is not in use. • Drops of water or condensation on the sensor window may cause the faucet to run. • If the LED in the sensor window flashes while the faucet is in use, the battery is low, but the faucet may still be used. If the LED stays on, the faucet will not run, and the battery must be changed. • If the power to the outlet or to the building fails, the 110 V version of the faucet will not run. • The spray pattern will be unattractive immediately after installation or service, due to air in the faucet. After the faucet is used 10 - 15 times, the spray pattern will clear. Installation Position the faucet on the sink or countertop (1). Install and tighten the mounting nut (2). Tighten the tensioning screws (3). Connect the 3/8” adapters to the stops (4). Connect the hoses to the adapters (5). Tighten the hoses with two wrenches, as shown, to prevent the hoses from twisting. 1 2 3 5 4 Connect the faucet power cable to the battery pack or AC power pack (1). Plug the AC power pack in. Turn the hot and cold supplies on (2). Remove the protective film from the sensor window (3). Wait 30 seconds before attempting to use the faucet (4). Position your hand in front of the sensor to turn the water on. Due to air in the faucet, the spray pattern may be unattractive for the first 10 - 15 uses after installation or service. 32110XX1/32112XX1 only: pull the temperature lever forward to make the water cooler, backward to make it warmer. 3 4 1 2 Temperature adjustment - 32111XX1 / 32113XX1 only Turn the water supplies off (1). Disconnect the faucet power cable from the battery pack or AC power pack (2). Remove the screw from the rear of the faucet (3). 3 2 1 Remove the faucet body (1). Turn the temperature screw forward to make the water cooler, backward to make it warmer (2). Dry any drops of water from the faucet or mounting surface. Replace the faucet body (1). Replace the screw (2). Turn the water supplies on (3). Reconnect the power cable (4). Wait 30 seconds (1). Place your hand in front of the faucet to turn it on (2). 1 2 1 2 3 4 Battery replacement -- models 32110XX1 / 32111XX1 only If the LED in the sensor window flashes, the battery is low, but the faucet can still be used. If the LED lights continuously, the battery must be changed before the faucet can be used. Remove the four screws and the battery pack cover. Remove the old battery (1). Install the new battery (2). Reinstall the battery pack cover. Wait 30 seconds (1). Activate the faucet by placing a hand in front of the sensor (2). 2 1 Clean the aerator and filters -- all models If the water flow is reduced over time, clean the aerator (a) and th...
Эта инструкция также подходит к моделям:Сантехника - Talis S Electronic Faucet 32110XX1 (1.67 mb)
Сантехника - Talis S Electronic Faucet 32110XX1 (1.67 mb)
Сантехника - Talis S Electronic Faucet 32112XX1 (1.67 mb)
Сантехника - Talis S Electronic Faucet 32113XX1 (1.67 mb)