Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
Remove water and sediment from the filter screen and fuel strainer. / 4. Reinstall the fuel strainer, reconnect the fuel lines and secure them with the clips. NOTE: Turn the fuel valve ON and check for leaks. 7. Rotor assembly Install the tine assemblies and side disks as illustrated below. NOTE: Use of the side disks is optional. They are designed to enhance till- ing operations and their use is recommended to: 1) keep the tiller aligned for furrowing (especially on slopes); 2) protect plants and other such objects when tilling around them; 3) prevent hooking the tines in objects such as chainlink and picket fences when tilling close to them. FWD “L” side 4 “R” side 8. TRANSPORTING/STORAGE Transporting l Turn off the fuel valve. l Keep the tiller level. Do not lay it on it side or lean it back on its handle- bars. l Tie the tiller down securely with a suitable strap or rope to prevent it from tipping over. -1 Preparation for storage (Over 30 days): l Drain the gasoline from the fuel tank and carburetor: c: Remove the fuel line from the fuel valve, and drain all gasoline from the fuel tank into a safe container. Remove the carburetor drain bolt to drain gasoline from the carburetor. Reinstall the fuel line and tighten the drain bolt securely. Turn the fuel valve OFF. I’ ---Y FUEL LINE DRAIN BOLT m Gasoline is flammable and exolosive under certain conditions. Do not smqke or allow flames or sparks near the equipment while draining fuel. l Pull the starter handle until resistance is felt. At this point the piston is coming up on its compression stroke and both the intake and the ex- haust valves are closed. This will help to protect the engine from inter- nal corrosion during storage. --t d l Drain the engine oil and refill the engine with fresh oil. l Clean the tiller and coat areas of possible rust with a light film of oil. ii l Coat the cylinder walls with oil. (If anticipated storage will exceed 1 year.) Remove the spark plug and pour two or three tablespoonsful of clean oil into the cylinder. Pull the starter handle slowly to distribute the oil over the cylinder walls. Leave the piston on its compression stroke to close the valves. Reinstall the spark plug. l Cover the tiller and store on a level surface in a dry, dust-free area. l Store the tiller in an upright position; otherwise, oil may enter the cylinder. 26 ; 9. TROUBLESHOOTING When the engine will not start; 1. Is there enough fuel? 2. Is the fuel valve on? 3. Is the engine switch ON? 4. Is gasoline reaching the carburetor? To check, loosen the drain bolt with the fuel valve on. Fuel should flow 5 out freely. Retighten the drain bolt. -I m If any fuel is spilled, make sure the area is dry before testing the spark plug or starting the engine. Fuel vapor or spilled fuel may ignite. DdAlN BOLT 5. Is there a spark at the spark plug? a. Remove the spark plug cap. Clean any dirt from around the spark plug base, then remove the spark plug. b. Install the spark plug in the plug cap. p c. d. Turn the engine Ground the side switch on. electrode to any engine ground and pull the recoil starter to see if sparks jump across the gap. ? -’ e. If there is no spark, replace the plug and check again. If OK, try to start the engine according to the instructions. 6. If the engine still does not start, take the tiller to an authorized Honda dealer. 10. SPECIFICATIONS Model F210 Power products descriotion code F210 Dimensions and weight Dry Weight 27.5 kg (60.6 lb) Length 1,250 mm (49.2 in) Width 585 mm (23.0 in) Height 960 mm (37.8 in) Engine Model GVIOOKI bwe Single cylinder, 4-stroke, forced side valve, gasoline air cooled, Displacement 90 cm3 (5.5 cu in) Bore x Stroke 50 x 46 mm (I .97 x 1.81 in) Ignition System Transistorized ignition Spark Plug BMR4A (NGK), Wl4MR-U (ND) Oil Capacity 0.4 P (0.42 US qt) Fuel Tank Capacity 0.9 0 (0.24 US gal) Clutch Internal expanding shoe Transmission oil capacity 0.95 e (I .o us qt) NOTE: Specifications are subject to change without notice. 11. WARRANTY SERVICE Owner Satisfaction Your satisfaction and goodwill are important to your dealer and to us. All Honda warranty details are explained in the Distributor’s Limited Warran- ty. Normally, any problems concerning the product will be handled by your dealer’s service department. If, you have a warranty problem that has not c been handled to your satisfaction, we suggest you take the following ti action: l Discuss your problem with a member of dealership management. Often complaints can be quickly resolved at that level. If the problem has already been reviewed with the Service Manager, contact the owner of the dealership or the General Manager. l If your problem still has not been resolved to your satisfaction, contact: c American Honda Motor Co., Inc. P.O. Box 50 Gardena, California 90247-0805 Telephone: (213) 604-2400 We will need the following information in order to assist you: - Your name, address, and telephone number - Product model and serial number - Date of Purchase - Deal...