Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
TILLER TO ADJUST HANDLE HEIGHT (See Fig. 15) Factory assembly has provided lowest handle height. Se lect handle height best suited for your tilling conditions. Handle height will be different when tiller digs into soil. • If a higher handle height is desired, loosen the four nuts securing handle panel to engine brackets. • Slide handle panel to desired location. • Tighten the four nuts securely. HANDLE PANEL ENGINE BRACKETS NUTS (ALSO 2 ON LEFT SIDE OF TILLER) FIG. 15 TINE ARRANGEMENT Your outer tines can be assembled in several different ways to suit your tilling or cultivating needs. CAUTION: Tines are sharp. Wear gloves or other protection when handling tines. NORMAL TILLING - 26" PATH (See Fig. 16) • Assemble holes “A” in tine hubs to holes “B” in tine shaft. FIG. 16 tine_4OUTER TINE INNER TINEHAIRPIN CLIP A B A B CLEVIS PIN MID-WIDTH TILLING - 24" PATH (See Fig. 17) • Assemble holes “A” in tine hubs to holes “C” in tine shaft. tine_5ACA C FIG. 17 12 SERVICE AND ADJUSTMENTS NARROW TILLING/CULTIVATING - 12-3/4" PATH (See Fig. 18) • Remove outer tines. tine_ 6INNER TINES ONLY FIG. 18 NOTE: When reassembling outer tines, be sure right tine assembly (marked “R”) and left tine assembly (marked “L”) are mounted to correct side of tine shaft. TINE OPERATION CHECK (See Fig. 19) WARNING: Disconnect spark plug wire from spark plug to prevent starting while checking tine operation. For proper tine operation, forward tine control lever must be against control body and all slack removed from inner wire of control cable when control is in the “OFF” (up) position. If lever and cable are loose, loosen cable clip at lower end of cable. Pull up on cable to remove slack, without extending spring on end of cable, and retighten cable clip. FINAL CHECK “OFF” POSITION • With tine control “OFF” (up), push down on handle to raise tines off the ground. • Slowly pull recoil starter handle while observing tines. Tines should not rotate. • If tines rotate, inner wire of control cable is too tight which is extending lower spring and engaging tines. Loosen cable clip and push down on cable only enough to relieve spring tension. Tighten cable clip. • Recheck in “OFF” position and adjust if necessary. FINAL CHECK “ON” POSITION • With tine control “ON” (held down to handle) push down on handle to raise tines off the ground. • Slowly pull recoil starter handle while observing tines. Tines should rotate forward. • If tines do not rotate, inner wire of control cable is too loose. Loosen cable clip and pull cable up to remove slack and retighten clip. • Recheck in “ON” position and adjust if necessary. NOTE: If “ON” position check required adjustment, re check “OFF” position adjustment to insure tines do not rotate when control is “OFF” (up). FIG. 19 handles_ 94FORWARD TINE CONTROL IN “OFF” (UP) POSITION BODY TINE CONTROL “ON” POSITION TINE CON TROL CABLE CABLE CLIP TO REMOVE BELT GUARD (See Fig. 20) • Remove two (2) cap nuts and washers from side of belt guard. • Loosen (do not remove) tine shield nut on underside of tine shield. • Pull belt guard out and away from unit. • Replace belt guard by reversing above procedure. Be sure slot in bottom of belt guard is under head of tine shield bolt and all nuts are tightened securely. CAP NUTS AND WASH ERS BELT GUARD TINE SHIELD NUT FIG. 20 TO REPLACE V-BELTS (See Figs. 21 and 22) Replace V-belts if they have stretched considerably or if they show cracks or frayed edges. There are two (2) V-belts -forward (inside) and reverse (outside). Belt guard must be removed to service belts. See “TO REMOVE BELT GUARD” in this section of manual. NOTE: Observe carefully routing of both belts and lo ca tion of all belt guides before removing belts. 13 IDLER ARM PIN ENGINE PULLEY IDLER ARM PIN ENGINE PULLEY SERVICE AND ADJUSTMENTS FORWARD MOTION (INSIDE) V-BELT ENGINE PULLEY IDLER ARMREVERSE IDLER PULLEY IDLER ARM PIN TRANS MISSION PUL LEY BELT GUARD BOLT BELT GUIDE V-BELT FORWARD IDLER PUL LEY REVERSE REVERSE (OUTSIDE) FORWARD MOTION (INSIDE) V-BELT ENGINE PULLEY TRANS MISSION BELT GUIDE PULLEY REVERSE IDLER PULLEY BELT GUIDE FORWARD IDLER PULLEY REVERSE (OUTSIDE) V-BELT belts_10ENGINE PUL- FORWARD REVERSE IDLER PULLEY LEY IDLER PULLEY FRONT VIEW REFERENCE REVERSE IDLER PULLEY FIG. 21 BELT REMOVAL • Remove reverse idler pulley from idler arm. • Remove reverse (outside) V-belt. • Remove forward (inside) V-belt from transmission pul ley first and then from engine pulley. BELT REPLACEMENT • Install new forward (inside) V-belt to engine pulley first then to transmission pulley. Be sure belt is positioned on inside groove of both pulleys, inside all belt guides and rests on idler pulley. • Before installing reverse (outside) V-belt, turn belt “in side out”. Twist so wide, flat surface of belt is to inside. • Wrap V-belt around reverse idler pulley and re as semble idler to idler arm. Tighten securely. Be sure belt is between reverse idler pulley and idler arm pin. • Install belt to outside groove of transmission pul...