Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
Figure 5–9: Reverse drive belt removal. Figure 5–10: Reverse drive belt removal. 6 Off-Season Storage If the tiller will not be used for a period longer than 30 days, the following steps should be taken to prepare the tiller for storage. 1. Clean the exterior of engine and the entire tiller thoroughly. Lubricate the tiller as described in the lubrication instructions. 2. We do not recommend the use of pressure washers to clean your unit. They may cause damage to electric components, spindles, pulleys, bearings or the engine. The use of pressure washers will result in shortened life and reduce serviceability. 3. Refer to the engine manual for correct engine storage instructions. 4. Wipe tines with oiled rag to prevent rust. 5. Store tiller in a clean, dry area. Do not store next to corrosive materials, such as fertilizer. NOTE: When storing any type of power equipment in an unventilated or metal storage shed, care should be taken to rustproof the equipment. Using a light oil or silicone, coat the equipment and especially any springs, bearings, and cables. Trouble Shooting Guide WARNING Trouble Possible Cause(s) Corrective Action Engine fails to start Fuel tank empty, or stale fuel. Throttle control lever not in correct starting position (if so equipped). Blocked fuel line. Dirty air cleaner. Choke not in ON position. Spark plug wire disconnected. Faulty spark plug. Engine flooded. Fill tank with clean, fresh gasoline. Fuel will not last over thirty days unless a fuel stabilizer is used. Move throttle lever to start position. Clean fuel line. Refer to the engine manual packed with your unit. Move switch to ON position. Connect wire to spark plug. Clean, adjust gap or replace. Refer to the engine manual packed with your unit. Engine runs erratic Unit running on CHOKE. Spark plug wire loose. Blocked fuel line or stale fuel. Vent in gas cap plugged. Water or dirt in fuel system. Dirty air cleaner. Carburetor out of adjustment. Move choke lever to OFF position. Connect and tighten spark plug wire. Clean fuel line; fill tank with clean, fresh gasoline. Fuel will not last over thirty days unless a fuel stabilizer is used. Clear vent. Drain fuel tank. Refill with fresh fuel. Refer to the engine manual packed with your unit. Refer to the engine manual packed with your unit. Engine overheats Engine oil level low. Dirty air cleaner. Air flow restricted. Carburetor not adjusted properly. Fill crankcase with proper oil. Refer to the engine manual packed with your unit. Refer to the engine manual packed with your unit. Adjust carburetor as instructed in separate engine manual. Tines do not engage Foreign object lodged in tines. Tine clevis pin(s) missing. Pulley and idler not in correct adjustment. Not shifting properly. Control cable not adjusted properly. Belt worn and/or stretched. Dislodge foreign object. Replace tine clevis pin(s). Take unit to authorized service dealer. Refer to Controls section of operator’s manual for proper shifting procedures. Adjust control cable (see assembly instructions). Replace belt. Tines skip over ground Improper rotation. Forward rotation should only be used on soil that has already been tilled, not on virgin soil. Wheels do not engage Clevis pin missing. Tiller is not being shifted properly. Control cable not adjusted properly. Belt worn and/or stretched. Replace clevis pin. Refer to Controls section of operator’s manual for proper shifting procedures. Adjust control cable (see assembly instructions). Replace belt. Do not move gear selection handle with the wheels or tines engaged. Make certain the unit is stopped completely before changing the gear selection. A partial engagement may be necessary when engaging tines. Do not push down on handles so that wheels are lifted off the ground while using tine drive, or the tiller could move backward and cause personal injury. Never attempt to make any adjustments while the engine is running, except where specified in operator’s manual. 16 123456278910111213141516505419202122232425262728293031323334353637383940414230373043272346474849555656 9 Illustrated Parts List Model 390 Series To order replacement parts, contact your local Cub Cadet dealer; or call our dealer locator number at 1 (877) 282-8684; or log onto 17 Ref. Part No. Part Description 1 712-0442 Acorn Lock Nut 1/4-20 2 736-3020 Flat Washer.271” I.D. x.630” O.D. 3 720-0270A Reverse Handle Grip 4 731-1600 Handle Cover w/o throttle 5 710-0779A Truss Mach. Scr. #10 x 1/2” Lg. 6 720-0274 Handle Grip 7 712-3006 Hex Nut 1/4-20 Gr.2 8 726-0135 Cap Speed Nut 9 686-0083 Clutch Handle Assembly 10 720-0269 Clutch Grip 11 710-0641 Hex Bolt 1/4-20 x 2.25” Lg. Gr.5 12 731-1645A Clutch Handle Holder 13 736-0140 Flat Washer.385” I.D. x.62” O.D. 14 686-0014A Reverse Handle Ass’y 15 736-0264 Flat Washer.344” I.D. x.62” O.D. 16 649-04040 Handle Assembly Comp. 19 749-1401 Handle Brace 20 736-0921 Lock Washer 1/2 21 710-3194 Hex Bolt 1/2-20 Gr. 5 22 786-0005 Depth Bar 23 714-0149B Cotter ...