Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
16 Bolo Tine-Single, Right Hand tine used on left side of tiller. Includes mounting hardware: two #9711 bolts (Ref l\lo.1), two #9913 lockwashers and two #9802 hex nuts (these last two items replace Ref No. 3).................................. Locknut-Hex Hd., 3/8-16.............. Bolt-Hex Hd„ 3/8-16x1-3/4" (tine holder to tiller shaft).................. Replacement Set of 16 Bolo Tines— including eight right hand tines, eight left hand tines; and all required assembly hardware..... REF PART No. NO. 50049-02 8 6 55019 18 7 55095-01 8 55095-02 2 9 9380 10 9338 DESCRIPTION QTY. Bolo Tine-Single, Left Hand tine used on right side of tiller. Includes mounting hardware: two #9711 bolts (Ref No. 1), two #9913 lockwashers and two #9802 hex nuts (these last two items replace Ref No. 3)................................. 8 Tine Holder-for bolo tines, left and right sides.................................. 2 Wheel & Tire Assy-Left Side......... 1 Wheel & Tire Assy-Right Side ..... 1 Clevis Pin—.312"x1 -3/4", secures wheel hub to wheel shaft........... 2 Hair Pin Cotter.............................. 2 BLUNT END TOWARDS YOU LEFT HAND TINE RIGHT HAND TINE IMPORTANT: Left and right sides of tiller are determined by standing in the operator position and facing the direction of forward travel. 11 TROY-BILT® TUFFY® TILLER MODELS 12060, 12077 TRANSMISSION HOUSING, COVERS, SEALS, GASKETS, AND PLUG 14 12 MODELS 12060, 12077 TROY-BILT® TUFFY® TILLER TRANSMISSION HOUSING, COVERS, SEALS, GASKETS, AND PLUG REF PART REF PART No. No. DESCRIPTION QTY. No. No. DESCRIPTION OTY 1 9467 Plug-Transmission Oil Fill/Check.. 1 7 9617 Oil Seal-D rives haft........................ 1 2 90038 Bolt-Hex Hd., Flange Lock, 8 9621 Oil Seal—Wheelshaft...................... 2 5/16-18x5/8", GR5.................... 8 9 55000 Transmission Case, Rear Housing 3 97037 Gasket-Transmission Oil Fill/Check and Tube Assembly................... 1 Plug........................................... 1 10 1909374 Oil Seal—Tine Shaft....................... 2 5 55008 Cover-Transmission Housing 11 55011-1 Gasket-Bearing Cap (.010" thick). 1 Front.......................................... 1 55011-2 Gasket-Bearing Cap (.030" thick).. 1 5A 50074 Cover-Transmission Housing, Rear 1 12 55010 Cap-Rear Bearing ........................ 1 6 50032 Gasket-Transmission Housing Cover 13 90045 Bolt-Flanged Hd., 5/16-18x1" ...... 2 (Front and Rear)........................ 2 14 90044 Bolt-Flanged Hd., 5/16-18x3/4".... 1 13 TROY-BILT® TUFFY® TILLER MODELS 12060, 12077 DRIVE SHAFT ASSEMBLY 14 MODELS 12060, 12077 TROY-BILT® TUFFY® TILLER DRIVE SHAFT ASSEMBLY REF PART No. No. DESCRIPTION OTY. 1 9655 Bolt-Hex Head, 5/16-24x3/4", Grade 5...................................... 2 9944 Washer—Belleville.......................... 3 55031 Pulley—Transmission..................... 4 9301 Key-Transmission Pulley, 3/16x1". 5 50027 Support Washer-Front.................. 6 9517 Snap Ring..................................... 7 1714 Bearing-Tapered Roller with race.. 8 50043 Support Washer-Rear................... 9 55001 DriveShaft Assembly..................... REF PART No. No. DESCRIPTION QTY. 1224-1 Shim-Rear Bearing Cap, .010" thick.......................... As Req’d 1224-2 Shim-Same as above except .030“ thick.......................... As Req’d 1224-3 Shim-Same as above except .005" thick.......................... As Req’d 1224-4 Shim-Same as above except .062" thick.......................... .As Req’d 1325C Shim Set—Includes the following shims: two #1224-1, two #1224-2, one #1224-3, and one #1224-4..As Req’d 15 TROY-BILT® TUFFY® TILLER MODELS 12060, 12077 WHEEL SHAFT & TILLER SHAFT ASSEMBLIES 16 MODELS 12060, 12077 TROY-ВILT© TUFFY® TILLER WHEEL SHAFT & TILLER SHAFT ASSEMBLIES REF PART No. No. DESCRIPTION QTY. 1 9512 Retainer-Snap Ring, “E” Type..... 2 2 9511 Retainer-Snap Ring.. ................... 4 3 1166-1 Shim-0.062" Thick... ..............As Req’d 1166-2 Shim-0.030" Thick... ..............As Req’d 1166-3 Shim-0.015" Thick... ..............As Req’d 1166-4 Shim-0.010" Thick... ..............As Req’d 1166-5 Shim-0.005" Thick... ..............As Req’d 4 1086 Bushing-Bronze....... ................... 4 REF PART No. No. DESCRIPTION QTY. 5 55004 Wheel Shaft..................................................................1 6 9305 Key-Wheel Shaft, Hi Pro, 1/4"x1" 1 7 1132-2 Spacer..................................................................................4 8 50041 Worm Gear-Wheel Shaft..........................1 9 55006 Tiller Shaft......................................................................1 10 1104 Woodruff Key—Tiller Shaft........................1 11 50042 Worm Gear—Tiller Shaft..............................1 17 TROY-BILT® TUFFY® TILLER MODELS 12060, 12077 ACCESSORIES BUMPER & CARBURETOR GUARD ATTACHMENT (Part No. 11405) (Viewed from front of ...