Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
Adjust the micrometer setting CALIBRATION 2. Squeeze the trigger against LINE 3. The front edge of the shutoff bar aligned with the calibration line engraved bottom of the hopper. 4. To adjust alignment, use a small wrench black calibration screw at the lower end wire leading from the micrometer insert. Spend a few minutes on maintenance after each use 2. After each use, wash thoroughly to remove all material clinging to the spreader. Hot water may be required at times to remove stubborn residue. Allow the spreader to dry thoroughly in the sun. 1. Never leave product in the spreader. Pour leftover material back into the package and seal the package tightly. 3. Store your spreader in a clean dry place. NOTE: This unit does not require lubrication Thank you for purchasing a Scotts ® AccuGreen ® 2000TM spreader. The Scotts Company introduced the first home lawn spreader in 1946 and has continued to offer superior quality that translates into more accurate application, a better- looking lawn, and a longer-lasting, more durable spreader. The lawn care industry’s most extensive research, design, and testing have gone into making the AccuGreen series spreaders the most accurate in their class. With its durable rustproof hopper, the AccuGreen ® 2000TM spreader is Questions, Comments, Information guaranteed to give you great results — now and for many years to come. Call Scotts’ toll- free “Lawn Success Made Easy” ™ Consumer Helpline: Visit Scotts’ website at ACCUGREEN 2000 75345 1- 800-543- TURF Scotts No-Quibble Guarantee ® If for any reason you, the consumer, are not satisfied STRIP IN UPC CODE after using this product, you are entitled to get your 0 32247 75345 6 money back. Simply send us evidence of purchase and we will mail you a refund check promptly. ® The Scotts Company 14111 Scottslawn Rd. Marysville, Ohio 43041 PROOF OF PURCHASE 125000912 01-AG2000 Printed in USA Printed on Recyled Paper ©2001, The Scotts Company. World rights reserved. DROP SPREADER Ready to use!No assembly! The Scotts Difference ® • Accurate application of lawn products • U-shaped handle with fingertip on/off control • Precision micrometer rate setting • Mid-Size hopper holds more than 7,500-square-feet of Scotts fertilizer • 18-inch spread width • Easy-rolling 12-inch wheels for stability and maneuverability • Rustproof hopper, agitator and polymer components • Scotts No-Quibble Guarantee ® • Made in the U.S.A. 1-800- 543-TURF SCOTTSTOLL- FREE INSTRUCTIONS INSIDE— SAVE FOR FUTURE REFERENCE AccuGreen2000 3/28/11:01 Page 2 To use your ® 2000spreader: TM 5. If the lawn product you purchased does not give the Scotts ® AccuGreen ® spreader, you can test for the proper setting. Set up the stand 1. Lay the spreader down so that it rests on the front of the hopper. Lift the stand and brace, Empty the number of pounds the recommends for then spread the sides of the brace and insert 1,000 square feet into the spreader. Adjust the spreader to a very the ends into the holes in the stand. low setting and spread product over a 1,000-square- foot area (50 by 20 feet, 33 by 30 feet, or equivalent). Adjust the setting 2. Place the spreader upright on its wheels. Raise upward after judging how much product has been applied to the the top half of the handle to the upright position test area. Remember: it is safer to under-apply with the test and and tighten the wing nuts by hand. With our increase setting later as needed. Some fertilizers can burn your patented locking wing nuts, no tools are needed. lawn if over- applied. NOTE: Reverse steps 1 and 2 for convenient, compact storage of your AccuGreen ® 2000TM spreader. Follow these application tips guaranteed results Set the spreading rate before you begin 1. If your lawn is rectangular, apply product the longest direction. Apply two header strips across each end For best results, use a Scotts Lawn for a turning area. Do not leave the spreader Fertilizer or Grass Seed Product. open as you turn— shut it off as you reach the 1. First check the back of your Scotts ® product end of a strip, then open it as you begin the package for the proper rate setting number next one. under the heading “Scotts Drop. ” Some If there are trees in the lawn, shut off the other lawn product manufacturers provide spreader just before getting to the trunk, then settings for Scotts drop spreaders, but using (A) TRIGGER move to the opposite side and continue with the CONTROL Scotts products will assure the best possible (B) (C) spreading pattern. results. (If you already purchased a product which does not provide a setting for Scotts 2. If your lawn is an irregular shape, apply a header drop spreaders, you can use the method strip completely around it. Then apply product described in #5. ) back and forth in the longest direction, shutting off the spreader when you reach the 2. Be sure spreader is turned off (trigger header strip. control is away from the handle) (A) . 3. Avoid “skips” or missed streaks. This me...