Оценок - 4, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
Know how to operate your tractor before using the broadcast spreader attachment. Read the chemica! label instructions and cautions for handling and applying the chemicals purchased for spreading. Wear eye and hand protection when handling and when applying lawn or garden chemicals. Never operate tractor and spreader attachment without wearing substantial footwear, and do not allow anyone to ride or sit on spreader attachment frame. Never allow children to operate the tractor or spreader attachment, and do not allow adults to operate without proper instructions. Always begin with the transmission in first (low) gear and with the engine at low speed, and gradually increase speed as conditions permit. Maximum towing speed -6 M.RH. When towing broadcast spreader do not drive too close to a creek or ditch and be alert for holes and other hazards which could cause you to goose control of the broadcast spreader and tractor. Before operating vehicle on any grade (hill) refer to the safety rules in the vehicle owner's manual concerning safe operation on slopes. Stay off steep slopes! Follow maintenance and lubrication instructions as outlined in this manual. Look for this symbo! to point out important safety precautions. It means-oAttention!! Become alert!! Your safety is involved. J REF. _QTY. DESCRIPTION A 4 Hex Bolt, 1/4" x 1o3/4" B 4 Hex Bolt, 1/4" x 2" C 1 Hitch Pin D 8 Nut, 1/4" E 1 Hair Cotter Pin, 1/8" CARTON CONTENTS 1. Spreader Assembly 4. Hitch Tube, LH. (Left Hand) 2. Contro! Cable 5. Hitch ControITube 3. Hitch Tube, R.H. (Right Hand) 6. Hitch Brackets (2) TOOLS REQUIRED FOR ASSEMBLY REMOVAL OF PARTS FROM CARTON , Remove a!l parts and hardware packages from the (2) 7/16" Wrenches carton. Lay out all parts and hardware and identify using the illustrations on page 3. AssemblevinylcapsontotheendsoftheR,H,and LH, HitchTubes,Seefigure1, AssembletheR,H,HitchTubetothespreaderframe tubeusingtwo1/4"x 2"hexboltsand1/4"nuts,Do nottightenyet. RepeatforLH,HitchTube,See figure1, AssembletheHitchBracketstotheHitchControl Tubeusingtwo1/4"x 1o3/4"hexboltsand1/4"nuts, Tighten,Seefigure3, Assemblethehitchpinthroughthehitchbracketsand securewiththe1/8"haircotterpin,Seefigure3, HmTCR PUN _ 1/4" x 1o314" / HEX BOLT _ 114"NUT 114".2" HEXBOLT FIGURE1 FIGURE 3 o Assemble the vinyl cap onto the Hitch Control Tube, Assemble the Hitch Control Tube between the Hitch See figure 4, Tubes using two 1/4" x 1o3/4" hex bolts and 1/4" nuts, ® Assemble the Control Cable to the Hitch Control Tube Tighten all bolts and nuts See figure 2, using the carriage bolt and nylon wing nut, See figure 4, CARRmAGE BOLT 114" NUT 114". 1o3/4" HEX BOLT FIGURE 2 FIGURE 4 KNOW YOUR SPREADER Read this owner's manual and safety rules before operating your Spreader. Compare the illustration below with your Spreader to familiarize yourself with the various controls and their locations. FLOW CONTROL LEVER ADJUSTABLE STOP FIGURE 5 FLOW CONTROL LEVER Opens and doses the flow plate on the bottom of the hopper. ADJUSTABLE STOP Allows the flow control lever to be moved to the same setting repeatedly. HOW TO USE YOUR SPREADER ADJUSTING THE FLOW RATE SETTING Loosen the wing nut that fastens the control to the handle. o Slide the Adjustable stop to the desired setting and retighten the wing nut. See figure 5. USING YOUR SPREADER Check the material package and the Spreader Settings sheet included with your spreader for the proper spreader setting and application rate. . Before filling spreader, move the control lever to the "OFF" position. Move spreader onto a flat surface -either a walk or a driveway -and fill. . Slide the Adjustable Stop to the desired setting. . Start the spreader in motion, then move the control lever fon_ard against the adjustable stop to begin spreading. NOTE: Always place control lever in the "OFF" position while filling spreader and when stopping or turning, to prevent release of excess fertilizer. APPLiCATiON TiPS This unit wii! cover a 4 to 8 foot wide area depending on the material used and the towing speed. . To avoid misses or striping, make each pass about 5 feet from the previous one so some overlapping of spread pattern does occur. . For easiest application, spread across the shortest edges of lawn first, making two "header" strips for a turning area, and then spreading between the header strips. See figure 6. . if lawn is odd shaped, spread a border around the edges and then spread between the border. See figure 6. . Keep wheel approximately 4 feet from any area you do not wish to spread. IMPORTANT: Be careful when using spreader around ornamental plants because weed control chemicaJs can damage these plants. FIGURE 6 CUSTOMER RESPONS_B_UT_ES Read and follow the maintenance schedule and the maintenance procedures listed in this section. MAINTENANCE SCHEDULE Fill in dates as you complete regular service. Check for loose fasteners X Lubrication X X X _,_-/" Service Dates CHECK FOR LOOSE FASTENERS Always empty spreader after each use, storin...