Оценок - 2, средний балл: 5
(
)
)
|
Фрагмент инструкции
214-200A assembly 214-255A VERTICAL ROTARY TILLERS yrnrrmTrrrrrrrrrrrrrerrrrrrrrrrrrrrmrrrrrroTffrrrrrrïifTrrnr^^ WARRANTY mr*» For one year from date of purchase, MTD Products Inc will replace for the original purchaser, free of charge, F.O.B. factory or authorized service firm, any part or parts found to be defective in material or workmanship. All transportation charges on parts submitted for replacement under this warranty must be paid by the purchaser. This warranty does not include replacement of parts which become inoperative through misuse, excessive use, accident, neglect, improper maintenance or alterations by unauthorized persons. This warranty does not include the engine, motor, battery, battery charger or any a component parts thereof. For service on these units, refer to the applicable manufacturer's warranty. ® O The above warranty will apply only to the original owner and will be effective only if the warranty « card has been properly processed. It will not apply where the unit has been used commercially. Warranty service is available through your local authorized service dealer or distributor. UNDER NO CIRCUMSTANCES WILL THE RETURN OF A COMPLETE UNIT BE ACCEPTED BY THE FACTORY UNLESS PRIOR WRITTEN PERMISSION HAS BEEN EXTENDED. gumuumjum»»nmn»»nmnijim»nimninmnnn«innmiiiw MTD PRODUCTS INC • 5389 WEST 130th STREET • P. 0. BOX 2741 CLEVELAND OHIO 44111 PRINTED IN U.S.A. FORM NO. 770-4923 I wm mus 1. Your tiller is a precision piece of power equipment. Exercise extreme caution at all times. 2. Do not attempt to start engine with the clutch control in the engaged or FORWARD position. 3. Stand clear of tines when starting engine. Never stand in front of, or work on tines while the engine is running. 4. NEVER place hands or feet in the vicinity of the tines while the engine is running. 5. Always stop engine when tiller is not in actual use. 6. Always disconnect spark plug wire during repairs or refueling operations. 7. Do not fill gas tank while engine is running. Do not spill gasoline on hot engine. Your rotary tiller is a precision built machine designed to take the work out of gardening and other related chores. It can be used for seed bed preparation, tilling, cultivating, furrowing, composting and mulching. Like any other piece of power equipment, it requires a certain amount of care and maintenance. In return for this, it will give a maximum of service and efficiency. Read these instructions carefully before assembling or operating your tiller. Through proper care and operation, you will obtain long, efficient service and trouble free operation. Handle — Assemble the handle brackets (10) to the handle (2) with hex head screw (13), lockwashers (11) and hex nuts (12). DO NOT tighten. Place the handle brackets (10) in the tail piece slots. Fasten the lower hole in the handle brackets to the frame with a carriage bolt 5/16-18 x%" Lg. (21), lockwasher (15) and hex nut (14). Tighten all screws and nuis. (See page 6.) CLUTCH CONTROL LEVER ASSEMBLY Lockout Lever — Assemble in this order: rubber washer (44), steel washer (43), lockout rod (45) (rod bracket to the front), steel washer (43) and lock nut (42). Tighten until rubber washer compresses slightly. (See page 6.) Clutch Control Assembly — Screw the ferrule (39) on the threaded end of the lock out rod (40) until about ’/2" of the threads show. Insert the ferrule through the control lever (38), fasten with flat washer (37) and hair pin cotter (36). Put the lockout handle in the neutral position. Insert the lockout rod in the bracket on the lockout lever and secure with a hairpin cotter (36) through the center of the bracket. Adjust the ferrule so both belts are slack when the lockout lever is in the neutral position. (See page 6.) Grips — Assemble grips (1) to handle bars. CHECK LIST BEFORE OPERATION 1. Check tiller tines for proper installation. With throttle lever set on STOP position and the clutch control handle set in FORWARD position, slowly crank engine to determine direction of tine rotation. Be sure all tines are mounted so the sharpened edges enter the soil first. ASSEMBLY Your rotary tiller is shipped complete in a single carton. The tines, wheels, handle and depth bar are to be assembled. This is done in the manner described below. Tines—Mount tines on tine shaft as shown. (See page 8.) Tines must be mounted with the cutting edges facing the front. The tiller will not operate properly unless the sharpened surface of the tines enter the soil first. Secure tines in position on tine shaft with cap screws (41), and nuts (32). Note: Dust pads (29 and 30) are provided in screw pack. These must be assembled as shown. (See Page 8.) Wheels — Insert axle bolts (25) and washer (28) into wheel hubs. Secure with nuts (31) and washers (30) tightened only enough to allow free movement of the wheels (27). Attach wheel and axle assemblies to outside of tiller legs (29) and (32). (See page 8.) 2. Check all nuts and b...
Эта инструкция также подходит к моделям:Садовые инструменты - 214-200A (1.32 mb)