Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Keeping your tiller in top running condition will prolong its life, and help you obtain optimum performance. Please read this normal care schedule, and note the recommended care operating intervals to extend the life of your unit. Maintenance Operation Page Before Each Use 50 hours or Every Season Check belt tension 13 X Change forward belt 13 X Engine maintenance 14 X X Check oil level/change oil 14 X 2 Clean tine axle shaft 14 X Lubrication 14 X Check throttle control adjustment -1 EM = See engine manual 1 Adjust throttle control after first three hours of operation or if engine is hard to start or run-on occurs. 2 Change oil after the first five to eight hours of use, then after every 50 hours or every season. Change oil every 25 hours when operating under heavy load or in high temperatures. SERvICING ThE ROTOTILLER ! WARNING The following information will help you make the necessary checks and perform the procedures required to follow the normal care To prevent accidental starting: recommendations made for your rototiller unit. If you prefer, your local authorized dealer can make these checks and perform the required procedures for you. Engine must be turned off and cool, and spark plug wire must be removed and secured from spark plug before checking and adjusting engine or equipment. Page 12 800- 45-6007 GetEarthquake.com OPERATor INSTRUCTIONS and parts Front Tine Models 3365_3365B_3365K_3365KPS_3365CE_3365PS_R3355H_3365PSCE Page 13 GetEarthquake.com 800-345-6007 Belt replacement part #: 3370 (forward) Chec k Belt Tension Belt tension may decrease over time. It must be adjusted within the first half hour of operation and checked after every two hours of operation. Proper adjustment will assure long belt life. Too much or too little belt tension will cause premature belt failure. To check and adjust the forward belt tension: 1. Turn off engine. Engine must be cool. 2. Remove spark plug wire from spark plug and secure. 3. With drive safety control lever in the neutral position, measure length of spring when in its relaxed state. 4. Pull down on drive safety control lever and measure length of spring when compressed. Ideal length would be 1/4” shorter. Change Forwar d Belt 1. Turn off engine. Engine must be cool. 2. Remove spark plug wire from spark plug and secure. 3. Remove front belt cover. • Remove the belt from the engine pulley: - G ently pull the engine recoil rope to rotate the pulley. - With the pulley turning, force the belt out of the V-groove. - Slide the belt free of the engine pulley. - Pull the belt down and out of the way. - Push the belt forward and out front of machine. • Install new belt: - Place belt in transmission pulley groove. - G ently pull the engine recoil rope to rotate the pulley while forcing the belt into the V-groove. 4. Replace front belt cover. 5. Attach spark plug wire. Chec k forwar d belt tension regularly . Too muc h or too little tension will cause premature belt failure . ! WARNING remove belt from front OPERATOR INSTRUCTIONS ANd PARTS Front Tine Models 3365_3365B_3365K_3365KPS_3365CE_3365PS_R3355H_3365PSCE ENGINE MAINTENANCE Refer to the engine manual included in your parts packet for information on engine maintenance. Your engine manual provides detailed information and a maintenance schedule for performing the following tasks: 1. Check oil level before each use or after every eight hours of operation. 2. Change oil after first five to eight hours of operation. Change oil while engine is warm. Refill with new oil of recommended grade. 4. Check spark plug yearly or every 100 hours of operation. 5. Service air cleaner. 6. Keep engine and parts clean. 7. Check engine and equipment often for loose nuts and bolts; keep these items tightened. ChECk OR FILL ENGINE CRANkCASE 1. Add oil according to engine manual. do not overfill. Use a clean, high-quality detergent oil. Container must be marked A.P.I.Service SF - SJ. Use no special additives with recommended oils. do not mix oil with gasoline. Oil level must be full. Check the oil level by removing oil fill plug. Oil level should be up to the bottom of the fill plug opening on most engines. 2. Always check oil level before starting engine. Refer to engine manual for capacity and type of oil to use. CLEAN TINE AxLE ShAFT 1. Turn off engine. Engine must be cool. 2. Remove spark plug wire and secure from spark plug. 3. Remove all vegetation, string, wire, and other material that may have accumulated on the axle between the inside set of tines and the seal on the transmission housing. 4. Replace spark plug wire. LUBRICATION Proper lubrication of moving mechanical parts is critical for proper care and maintenance. Oil the moving parts using a 30-weight oil. IMPORTANT ENGINE IS ShIPPEd FROM FACTORYWIThOUT OIL. YOU MUST Add ENGINE OIL BEFORE STARTING ENGINE. ENGINE CAN OvERhEAT ANd BECOME dAMAGEd IF dEBRIS BLOCkS ThE COOLING SYSTEM OR ROTATING SCREEN. NEvER RUN ENGINE WIThOUT COMPLETE AIR CLEANER INSTALLEd ON ENGINE. ! CAUTION d...
Эта инструкция также подходит к моделям:Садовые инструменты - EARTHQUAKE 3365 (4.34 mb)
Садовые инструменты - EARTHQUAKE 3365B (4.34 mb)
Садовые инструменты - EARTHQUAKE 3365PSCE (4.34 mb)
Садовые инструменты - EARTHQUAKE MODEL 3365CE (4.34 mb)