Оценок - , средний балл: ( )

Инструкция по эксплуатации Poulan, модель 952711880

Производитель: Poulan
Размер: 319.15 kb
Название файла:

Язык инструкции:

Документ загружается, подождите пожалуйста

Скачать инструкциюЗакрыть

Документ загружается, подождите пожалуйста

Скачать инструкциюЗакрыть

S For mowing or sweeping, use full throttle for a good clean job. TRIMMING - --Hold the bottom of the trimmer head about 3 inches (8 cm) above the ground and at an angle. Allow only the tip of the line to make contact. Do not force trimmer line into work area. Trimming3inches(8cm) aboveground SCALPING - --The scalping technique removes unwanted vegetation down to the ground. Hold the bottom of the trimmer head about 3 inches (8 cm) above the ground and at an angle. Allow the tip of the line to strike the ground around trees, posts, monuments, etc. This technique increases line wear. SWEEPING- --Thefanningactionoftherotatinglinecanbeusedtoblowawayloosedebrisfromanarea. Keepthelineparalleltoandabovetheareasurfaceandswingthetoolfromsidetoside. Sweeping OPERATING INSTRUCTIONS FOR USE WITH WEED BLADE S Blade Thrust is a reaction that only occurs when using a bladed unit. This reaction can cause serious injury such as amputation. Carefully study this section. It is important that you understand what causes blade thrust, how you can reduce the chance of its occurring, and how you can remain in control of unit if blade thrust occurs. S WHAT CAUSES BLADE THRUST --Blade Thrust can occur when the spinning blade contacts an object that it does not cut. This contact causes the blade to stop for an instant and then suddenly move or “thrust” away from the object that was hit. The “thrusting” reaction can be violent enough to cause the operator to be propelled in any direction and lose control of the unit. The uncontrolled unit can cause serious injury if the blade contacts the operator or others. S WHEN BLADE THRUST OCCURS -Blade Thrust can occur without warning if the blade snags, stalls, or binds. This is 12 more likely to occur in areas where it is difficult to see the material being cut. By using the unit properly, the occurrence of blade thrust will be reduced and the operator will be less likely to lose control. S Cut only grass, weeds, and woody brush up to 1/2 inch (1 cm) in diameter with the weed blade. Do not let the blade contact material it cannot cut such as stumps, rocks, fences, metal, etc., or clusters of hard, woody brush having a diameter greater than 1/2 inch (1 cm). S Keep the blade sharp. A dull blade is more likely to snag and thrust. S Cut only at full throttle. The blade will have maximum cutting power and is less likely to bind or stall. S “Feed” the blade deliberately and not too rapidly. The blade can thrust away if it is fed too rapidly. S Cut only from your left to your right. Cutting on right side of the shield will throw debris away from the operator. S Use the shoulder strap and keep a firm grip on the unit with both hands. A properly adjusted shoulder strap will support the weight of the unit, freeing your arms and hands to control and guide the cutting motion. S Keep feet comfortably spread apart and braced for a possible sudden, rapid thrust of unit. Do not overreach. Keep firm footing and balance. S Keep blade below waist level; it will be easier to maintain control of unit. S Do not raise the engine above your waist as the blade can come dangerously close to your body. S Do not swing unit with such force that you are in danger of losing your balance. Bring the engine to cutting speed before entering the material to be cut.If the blade does not turn when you squeeze the throttle trigger, make sure shaft is fully inserted into the engine. Always release the throttle trigger and allow engine to return to idle speed when not cutting. The blade should not turn while the engine is running at idle. If the blade turns at idle, do not use your unit. Refer to the CARBURETOR ADJUSTMENT section or contact your authorized service dealer. S Maintain good firm footing while using the unit. Do this by planting feet firmly in a comfortable apart position. S Cut while swinging the upper part of your body from left to right. S As youmoveforward to thenextarea tocut, be sure to maintain your balance and footing. RECOMMENDED CUTTING POSITION 2o’clock Cut using the 2 o’clock to 4 o’clock position of the 4 o’clock blade WARNING: The operator or others must not try to clear away cut material with the engine running or the blade turning to avoid serious injury. Stop engine and blade before removing materials wrapped around blade or shaft. ADDITIONALSAFETYRULESFOROPTIONALATTACHMENTS WARNING: For each optional attachment used, read entire instruction manual before use and follow all warnings and instructions in manual and on attachment. WARNING: Ensure handlebar remains installed on upper shaft (engine end of unit) at all times. Handlebar EDGERSAFETY WARNING:Inspecttheareatobeedgedbeforeeachuse.Removeobjects(rocks,brokenglass,nails,wire,etc.)whichcanbethrownbythebladeorcanwraparoundtheshaft. WARNING: Blade rotates momentarily after the trigger is released or engine is turned off. The blade can seriously cut you or others. Allow blade to stop before removing it from the cut. S Throw away blades that are bent, war...