Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
Pulling down on drive control levers engages the wheels and tines. Releasing drive control levers disengages the wheels and brings the tiller to a complete stop. It is now in the neutral position. Drive Control Levers Engaged CAUTION This information is provided here only to introduce the controls. DO NOT START THE ENGINE ATTHIS TIME. Starting and operating instructions are given on page 13. Please read this section and all operating and safety instructions before starting your tiller. CAUTION ENGINE SHOULD BE OFF BEFORE ADJUSTING ANY CONTROLS! v As a safety precaution, the drive control levers will not lock in the forward position. v To stop the wheels and tines at any time, release the drive control levers. Page 6 Controls REVERSE HANDLE (616RT) CAUTION Engages wheels and tines in reverse. Extreme caution should be used when operating rototiller in the reverse direction. Pulling reverse handle back towards operator reverses tiller. Drive Control Levers Released Reverse Handle v As a safety precaution, the reverse handle will not lock in reverse. v To stop the wheels and tines at any time, release the reverse handle. v Do not operate both the reverse handle and drive control levers at the same time. Page 7 Controls ENGINE CONTROLS Model 616RT Intec Engine Model 616RT Intec Engine Model 514RT Engine Throttle Control Move throttle control to fast position to start and run the engine.To stop the engine, move to idle position, then to off. Choke Control Put choke control in choke position if engine is cold. A warm engine requires less choking than a cold engine. Refer to your engine manual for further information. Model 616RT 1. Spark plug wire 2. Air cleaner 3. Choke 4. Carburetor 5. Fuel shut-off valve (if equipped) 6. Rope handle 7. Finger guard 8. Stop switch (if equipped) 9. Fuel fill 10. Fuel tank 11. Oil fill/Dipstick (if equipped) 12. Blower housing 13. Oil drain plug 14. Oil fill cap 15. Engine Id plate 16. Muffler Page 8 Adjustments SECTION CHECKLIST Wheel Lockouts Handlebar Adjustments (Tilt & Swivel) Drag Stake Belt Tension Adjustment WHEEL LOCKOUTS (616RT) Place wheels in tilling position. 1. Pull knob in center of wheel out, away from machine. 2. Rotate knob and lockout to align with slot on axle, release knob. Rotate wheel to align slot in wheel hub with lockout. 3. Wheel and axle should be firmly locked together before tilling. 4. Repeat for other wheel. Wheel lockout in tilling position. (hub & axle slot) Model 616RT (6-hp) NOTE: Always have both wheel lockouts in or out. Do not operate tiller with only one wheel locked. To place wheels in free-wheel position. 1. Pull knob in center of wheel out, away from machine . 2. Rotate knob and lockout to align lockout with detent in end of axle. Release knob. 3. Wheel should turn freely on axle. WHEEL LOCKOUTS (514RT) Place wheels in tilling position. 1. Remove lockpin. Align hole in axle with hole in wheel hub. 2. Insert lockpin through holes, fold lockpin ring to secure pin to axle. 3. Wheel and axle should be firmly locked together before tilling. 4. Repeat for other wheel. Model 514RT (5-hp) Wheel lockpin in free-wheel position. (axle hole only) NOTE: Always have both wheel lockouts in or out. Do not operate tiller with only one wheel locked. To place wheels in free-wheel position. 1. Remove lockpin. Slide wheel inward toward machine. 2. Insert pin in axle only. 3. Wheel should turn freely on axle. CAUTION Never start engine or operate tiller with wheels in freewheel position. The free-wheel position is for transporting the tiller long distances over level ground- do not attempt to move the tiller up or down steep grades in the free-wheel position. Page 9 Adjustments Handlebar Tilt Lever Handlebar Swivel Lever Model 616RT HANDLEBAR ADJUSTMENTS (616RT) Tilt handlebars up or down, swivel 30°left orright. ToTilt Up or Down: 1. Push down on handlebar tilt lever. 2. While holding tilt lever down, adjust handlebars to a comfortable height by moving up or down.There are 4 height positions. 3. Release handlebar tilt lever to lock. To Swivel 30° °°°°°Left or Right: 1. Squeeze handlebar swivel lever towards handlebar stem. 2. While holding handlebar swivel lever in, rotate handlebar 30° left or right. 3. Handlebars will lock in place after handlebar swivel lever is released. HANDLEBAR ADJUSTMENTS (514RT) Adjust handlebar height. The ideal height of the handlebar varies with operator height and the depth of tilling. to adjust handlebar height: 1. Unscrew T-Clamp until handlebar moves freely up and down. 2. Align locator pin to desired hole in the height adjustment bracket by raising or lowering handlebars. 3. Retighten T-Clamp firmly. high medium low T-clamp Model 514RT 3 HANDLEBAR HEIGHT SETTINGS Page 10 Page 11 DRAG STAKE Tilling depth is controlled by the height of the drag stake. To adjust tilling depth. 1. Remove detent pin. 2. Raise the drag stake to position tines at chosen tilling depth. 3. Align hole in drag stake with hole in depth regulator bracket...
Эта инструкция также подходит к моделям:Садовые инструменты - 1693207 (1.21 mb)
Садовые инструменты - 1693705 (1.21 mb)