Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
DO NOT OIL SELF-LUBRICATED WHEEL BEARINGS. REPAIRS To prevent rust, sand off and paint any parts or areas which become chipped or damaged. Tighten all bolts, capscrews, nuts, and fasteners securely. OFF-SEASON STORAGE If tiller is to be stored over 30 days proceed as follows: 1. Clean fuel screen and bowl. See Maintenance section of this manual. 2. Drain fuel tank and lines by placing suitable container under fuel shut-off valve and opening valve. Store gasoline in container using a gasoline stabilizer or additive. This additive prevents formation of gum and varnish for up to one year. 3. Operate engine until gasoline in carburetor is completely consumed. 7 4. While engine is still warm, drain oil from crankcase. See Maintenance section of this manual. Refill with fresh oil. 5. Remove spark plug, pour one ounce (2 or 3 tablespoons) of SAE 30 oil into cylinder and crank slowly to distribute oil. Replace spark plug. 6. Clean dirt and chaff from cylinder head fins and blower housing. TROUBLESHOOTING IF ENGiNE FAILS TO START 1. See Figure 9. Fuel tank may be empty. 2. See Figure 4. Throttle lever is not set halfway between SLOW and FAST position. 3. Spark plug is not securely connected. 4. See Figure 11. Choke plunger is not pulled out to full CHOKE position or, if engine appears flooded, pushed in, to clear excess fuel. To clear a flooded engine, push choke plunger completely in and pull starter rope several times. IF BELT SLIPPAGE OCCURS 1. Belt may be stretched or worn excessively. Replace belt. 2. Belt may be greasy or oily. If so, use cleaning fluid on a rag to clean. 3. Pulleys may be misaligned. Refer to Pulley Adjustment in Adjustments section of this manual. 4. Belt tension may be too loose. Refer to Clutch in Adjustments section of this manual. 8 SPECIFICATIONS MAKE: BRIGGS & STRATTON ■ MODEL NO: 80200 ■ STROKE: 1-3/4 Inches TYPE NO.: 0252-01 _ ■ CYCLES: 4 ■ DISPLACEMENT: 7.75 Cu. In. ■ CYLINDERS: 1 ■ CRANKSHAFT ■ BORE: 2-3/8 Inches PLANE: Horizontal STARTER Manual Rewind, easy spin CHOKE Manual ENGINE GOVERNOR Adjustable Mechanical, 1800 - 4000 RPM IGNITION Magneto LUBRICATION Gear Impeller System - 40% Slope Operation CRANKCASE CAPACITY: 1-1/4 Pints FUEL CAPACITY 2 Quarts AIR CLEANER Sealed Joint Housing, Reusable Oiled Foam Element MUFFLER Quiet, Low Back Pressure Type, Side Discharge TYPE Worm and Gear MATERIAL WORM: Carburized Steel GEAR: Bronze BEARINGS FRONT: Tapered Roller Bearing TRANSMISSION REAR: Tapered Roller Bearing SEALS DOUBLE LIP: Dirt Excluding LUBRICATION Special Worm Gear Oil (See back cover). HOUSING Cast Iron CLUTCH Touch-O-Matic V-Belt TYPE Self-sharpening, non-winding MATERIAL Forged, High-Carbon Steel TILLING WIDTH 21-1/2 In. Standard, 31-1/4 In. with Tine Extensions TILLING DEPTH 0 to 7 Inches, Adjustable TINES ATTACHMENTS TO HUB: Bolted TO SHAFT: Pin and Cotter Pin DRIVE INNER: Pin Type Floating Drive OUTER: Pin and Torsion Plate Floatinq\Drive SPEED 75 RPM at Full Engine Speed DEPTH ATTACHMENT Pin and Hairpin Clip BAR ADJUSTMENT 0 to 7 Inches Tilling Depth LOCATION FORWARD CLUTCH: Right Handle, Top CONTROLS THROTTLE: Left Handle REWIND STARTER AND CHOKE: On Engine FRAME Heavy-Duty, Electrically Welded with Cross-Bracing CHASSIS TIRES 8x1.75 Solid Rubber WHEEL BEARINGS Solid, Sintered Iron LENGTH 51 Inches WIDTH 26 Inches (Without Tine Extensions) OVERALL HEIGHT TO TOP OF HANDLE: 38-1/4 Inches DIMENSIONS TO TOP OF ENGINE: 27-3/4 Inches WEIGHT NET (DRY): 113 Lbs. SHIPPING (DRY): 123 Lbs. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. 3H.P. TILLER ENGINE PULLEY & CONTROL GROUP Ref. No. Part No. Qty. Description 1 118464 1 ENGINE 2 919354 4 CAPSCREW, Hex, 5/16 18x2 3 917642 8 WASHER, Flat, 5/16 4 917356 4 LOCKWASHER, 5/16 5 917372 4 NUT, Hex, 5/16-18 6 118463 6 SHIM 7 118470 1 PULLEY, Driven 8 118027 1 PULLEY, Engine 9 905850 1 KEY, Square 10 928691 1 SETSCREW, Cup 11 118312 1 BELT, "V" 12 154534 1 PULLEY, Idler Ref. No. Part No. Qty. Description 13 118335 1 SPACER 14 917642 1 WASHER, Flat, 5/16 15 921971 1 CAPSCREW. Hex, 3/8-16 x 1-3/4 16 916965 1 LOCKWASHER, 3/8 17 916950 1 NUT, Hex, 3/8 18 1609352 1 LEVER, Idler pulley 19 171337 1 BOLT, Pivot 20 923362 1 LOCKNUT. Hex, 5/16 21 106545 1 STOP, Belt 22 118037 1 STOP, Beit 23 909589 1 LOCKWASHER, 1/2 24 921370 1 CAPSCREW, Hex, 1/2-20 x 1 11 3H.P. TILLER Ref. No. Part No. Qty. Description 1 118400 1 SHIELD 2 118393 1 SEAL. Oil 3 118396 2 RING, Retaining 4 154393 2 CUP, Bearing 5 154486 2 CONE, Bearing 6 170888 1 SHAFT, Worm 7 118439 1 KEY 8 911171 1 KEY, 3/16x7/8 9 118399 1 CUP 10 118392 1 HOUSING, Worm drive 11 118462 1 PLUG, Vent 12 901653 1 PIPE, Plug 3/8 13 118492 1 WORM, R.H. 14 118398 1 SPACER 15 154487 1 CAP, Hub 16 118021 1 SHAFT, Worm gear 17 118403 2 SHIELD 18 118118 2 SEAL, Oil 19 118020 2 BEARING, Needle 20 118315 2 WASHER, Thrust 21 118022 1...
Эта инструкция также подходит к моделям:Садовые инструменты - 1600373 (897.8 kb)
Садовые инструменты - 1600399 (897.8 kb)