Оценок - 2, средний балл: 4 ( )

Производитель: Tanaka Размер: 390.67 kb Название файла: Язык инструкции:

CAUTION! Indicates a possibility of personal injury or equipment damage, if instructions are not followed. NOTE! Helpful information for correct function and use. 3 custsvc@tanaka-ism.com Owner.s ManualTPE-2501,TPE-2510,TPE-270PF/PN,TPE-250PF TPE-2501,TPE-2510,TPE-270PF/PN,TPE-250PF 3. Assembly procedures. Drive shaft to engine (Fig. 1 -1) Loosen tube locking bolt (1) about ten turns so that the bolt point will not obstruct drive shaft tube to be inserted. When inserting drive shaft tube, hold the tube locking bolt outward preventing inside fitting from obstructing as well. Insert the drive shaft into the clutch case of the engine properly until the marked position (2) on the drive shaft tube meets the clutch case. NOTE! When it is hard to insert drive shaft up to the marked position on the drive shaft tube, turn drive shaft by the cutter mounting end clockwise or counterclockwise. Tighten tube locking bolt lining up the hole in the shaft tube. Then tighten clamp bolt securely (3). Installation of handle (Fig. 1-2) Attach the handle to the drive shaft tube with the angle towards the engine. Adjust the location to the most comfortable position before operation. Throttle wire/stop cord Remove air cleaner cover. (Fig. 1-3) Connect stop cords. (Fig. 1 -4) Connect throttle wire end to carburetor. (Fig. 1 -5) Cover throttle wire and stop cords together with protective tube provided up to air cleaner cover. (Fig. 1-6) 4 custsvc@tanaka-ism.com Owner.s ManualTPE-2501,TPE-2510,TPE-270PF/PN,TPE-250PF TPE-2501,TPE-2510,TPE-270PF/PN,TPE-250PF Installation of blade guard (Fig. 1-7) 1) Install blade guard (1) on gear case (4) temporarily by clamping with guard brackets (2) and screws (3). Then tighten as needed. 2) Line up the slot of guard bracket (2) with the same of gear case (4), then tighten screws (3) securely. (Fig. 1-7B) Installation of wheel (Fig. 1-7C) 1) Installation the wheel as the illustration. 2) After installation, check if the wheel turns smoothly. Installation of blade (Fig. 1-8) 1) Before installation of blade, take off left hand threaded fixing nut (1), cutter holder cap (2) from the blade shaft. 2) Install blade (3) on the shaft and then replace the cutter holder cap and fixing nut in order. NOTE! When installing cutter holder cap (2), be sure to set concave side facing blade. 3) Insert the locking bar (4) into the hole of the cutter holder (5) and gear case by lining up each hole. 4) Tighten the fixing nut securely (clockwise to loosen/counter-clockwise to tighten). 5 custsvc@tanaka-ism.com Owner.s ManualTPE-2501,TPE-2510,TPE-270PF/PN,TPE-250PF TPE-2501,TPE-2510,TPE-270PF/PN,TPE-250PF 4. Operating procedures. WARNING! This unit is equipped with a two-stroke engine. Always run the engine on fuel, which is mixed with oil. Provide good ventilation, when fueling or handling fuel. Fuel • Always use branded 89 octane unleaded gasoline. • Use Tanaka two-cycle oil or a quality two-cycle oil at mixing ratio of 25-50:1 (Gasoline (A) : Oil (B)), only for the state of California at 50: 1. • Never use multi-grade oil (10 W/30) or waste oil. • Always mix fuel and oil in a separate clean container. Always start by filling half the amount of fuel, which is to be used. Then add the whole amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of fuel. Mix (shake) the fuel-mix thoroughly before filling the fuel tank. Fueling WARNING! • Always shut off the engine before refueling. • Slowly open the fuel tank, when filling up with fuel, so that possible over-pressure disappears. • Tighten the fuel cap carefully, after fueling. • Always move the unit at least 3 m (10 ft.) from the fueling area before starting. Before fueling, clean the tank cap area carefully, to ensure that no dirt falls into the tank. Make sure that the fuel is well mixed by shaking the container, before fueling. 6 custsvc@tanaka-ism.com Owner.s ManualTPE-2501,TPE-2510,TPE-270PF/PN,TPE-250PF Starting (Fig. 2-2) TPE-2501,TPE-2510,TPE-270PF/PN,TPE-250PF Starting (Fig. 2-2) CAUTION! Before starting, make sure the cutting attachment does not touch anything. 1. Set ignition switch (1) to ON position. *Push priming bulb (4) several times so that fuel flows through bulb into carburetor. (if so equipped)(Fig. 2-2B,3) 2. With the safety lever (2) pressed (if so equipped), pull throttle trigger and push lock button (3), then slowly release the throttle trigger first, then the safety lever. This will lock the throttle in starting position. 3. Set choke lever to CLOSED position (5). (Fig. 2-2B,3) 4. Pull recoil starter briskly, taking care to keep the handle in your grasp and not allowing it to snap back. 5. When you hear the engine want to start, return choke lever to RUN position (open). Then pull recoil starter briskly again. NOTE! If engine does not start, repeat procedures from 2 to 5. 6. After starting engine, pull throttle lever to release lock button. Cutting (Fig. 2-...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: