Оценок - 4, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
If you do not know the dealer or distributor in your area, please write to the Customer Service Department of MTD. The return of a complete unit will not be accepted by the factory unless prior written permission has been extended by MTD. This warranty gives you specific legal rights. You may also have other rights which vary from state to state. Your new tiller attachment comes unassembled from the factory. You will need two adjustable wrenches and one hammer to complete the assembly of your tiller. 1ST OF CONTENTS IN HARDWARE PACK. (See figure 1) A (4) Hex Screws 5/8-11 x 1-1/2" long B (6) Lockwashers for 5/8" screw C (4) Hex Screws 1/2-13 x 1-1/4" long D (4) Lockwashers for 1/2" screw E (4) Spring pins 3/8" Dia. x 2" long F (3) Hair pin cotters for 5/8" Dia. G (2) Link Clevis Pins H (2) Hex Lock Nuts 5/8-18 Thread I (1) Clevis Pin 5/8" Dia. x 2" long J (4) Hex Screws 5/16-24 x 3/4" long K (4) Lockwashers for 5/16" screw L (4) Hex Nuts 5/16-24 Thread M (2) Hair Pin Cotters for 3/8" Dia. N (2) Clevis Pins 3/8" Dia. x 1-1/4" long 0 (1) Spring Pin 5/16" Dia. x 1-3/4" long P (1) Square Head Pipe Plug-Vented Q (10) Carriage Bolts 5/16-18 x 1" long R (10) Lockwashers for 5/16" Screw S (10) Hex Nuts 5/16-18 Thread FIGURE 1 ASSEMBLY INSTRUCTIONS 1. Remove the tiller, all loose parts and hardware parts pack from the carton before discarding the carton. 2. Place the gear box so that the pipe plug is up, as shown in figure 2. FIGURE 2 3. With an adjustable wrench remove the pipe plug and replace with vented pipe plug (P) provided in hardware parts pack. See figure 2. 4. Assemble the right and left hand tine assemblies to gear box, with four spring pins (E). A hammer is required. See note below before continuing. NOTE Right and left hand is determined from behind the gear box. The sharp edge of the tines must enter the soil first. See figures 3 and 4. 3 FIGURE 3 FIGURE 4 FIGURE 6 5. Install tiller pivot bracket assemblies. An adjustable wrench is required. Place pivot bracket in position on gear box as shown in figure 5. Secure with four hex screws (A) and lockwashers (B). See figure 5. FIGURE 5 6. Insert link clevis pins (G) through outside holes of pivot bracket assemblies. Using two adjustable wrenches, tighten link clevis pins in place with lockwashers 5/8" (B) and hex center lock nuts 5/8-18 (H). See figure 6. 7. Install cover bracket assembly to gear box (as shown in figure 7) using four hex screws 1/2-13 x 1-1/4" (C) and 1/2" lockwashers (D). An adjustable wrench is required. NOTE All hex screws should be hand tightened. When _a[l_ screws are in place, then tighten with adjustable wrench. FIGURE 7 Place tiller cover assembly in position on the tiller cover bracket as shown in figure 8. Using six 1" carriage bolts (Q), six 5/16" lockwashers (R) and six 5/16-18 hex nuts (S) start by hand. Do Not Tighten. a. Place two of the carriage bolts in the top center of the cover first. See figure 8. b. Place the next two carriage bolts in the rear of the cover as shown in figure 8. c. Place two more carriage bolts in the front of the cover as shown in figure 8. d. Do not tighten any of the six bolts in step 8 until step 9 is completed. 10. Using an adjustable wrench, tighten all ten carriage bolts used in steps 8 and 9. 11. Block up the front of the tiller so that the input shaft is clear of the ground. Place the universal drive shaft in posi...
Эта инструкция также подходит к моделям:Садовые инструменты - 199-956A (1.98 mb)
Садовые инструменты - 199-981A (1.98 mb)
Садовые инструменты - 19956-9 (1.98 mb)