Оценок - 4, средний балл: 4.3 ( )

Производитель: Stihl Размер: 2.04 mb Название файла: Язык инструкции:

Always press spark plug boot ( 2) snugly onto spark plug terminal ( 1) of the proper size. ( Note: If terminal has detachable SAE adapter nut, it must be attached. ) A loose connection between spark plug boot and ignition wire connector in the boot may create arcing that could ignite combustible fumes and cause a fire. If engine running behavior is unsatisfactory even though the air filter is clean and the carburetor and throttle cable are properly adjusted, the cause may be in the muffler. Have your STIHL dealer inspect the muffler for carbonization. STIHL recommends that maintenance and repair work be carried out only by authorized STIHL dealers. FS 300, FS 350, FS 400, FS 450, FS 480 English / USA Lubricating the Gearbox 1 2 256BA044 KN Replacing the Starter Ropeand Rewind Spring 1 11 1 256BA063 KN 3 2 4 256BA032 KN 6 5 256BA033 KN Use STIHL gear lubricant for brushcutters (see " Guide to Using this Manual" ) . : : : : : Check grease level about every 100 hours of operation. Unscrew the filler plug ( 1). If no grease can be seen on the inside of the filler plug, screw the tube of lubricant ( 2) into the filler hole. Squeeze grease into the gear housing – till 1/ 5 oz (5 g). Do not completely fill the gear housing with grease. Refit the filler plug and tighten it down firmly. Replacing the starter rope The rewind spring may pop out and uncoil – take care to avoid injury during the following operation. : Remove the screws ( 1). : Lift away the fan housing. : Remove the spring clip ( 2). : Carefully pull off the rope rotor with washer ( 3) and pawl ( 4). : Ease the cap ( 5) out of the starter grip. : Remove remaining rope from the rotor and grip. : Tie a simple overhand knot in the end of the new starter rope (see Specifications) and then thread the rope through the top of the grip and the rope bush ( 6). : Refit the cap in the grip. FS 300, FS 350, FS 400, FS 450, FS 480 English / USA 256BA034 KN 3 2 4 256BA032 KN : Thread the rope through the rotor and secure it in the rotor with a simple overhand knot. : Lubricate the rope rotor bearing bore with non-resinous oil (Special Accessories) . : Slide rotor onto starter post – turn it back and forthe until the loop of the rewind spring engages. : Fit the pawl ( 4) and washer ( 3), and press the spring clip ( 2) into position. The spring clip must point counter- clockwise and engage the peg on the pawl. 427BA016 KN Tensioning the Rewind Spring : Make a loop in the unwound starter rope and use it to turn the rope rotor six full revolutions in the direction of the arrow (see illustration). : Hold the rotor steady – straighten the twisted rope. : Seilrolle loslassen : Release the rotor and let go of rope slowly so that it winds onto the rotor. The starter grip must sit firmly in the rope guide bush. If the grip droops to one side: Increase spring tension by one additional turn. When the starter rope is fully extended it must be possible to rotate the rotor at least another half turn (FS 300, 350) or one and a half turns (FS 400, 450, 480)). : : If this is not possible, the spring is overtensioned and could break. Take one turn of the rope off the rotor. Fit the fan housing. Replacing the Rewind Spring Broken parts of the spring may still be under tension and could be thrown in your direction when you pull off the rope rotor and remove the spring housing. To reduce the rist of injury, wear eye and face protection and work gloves for the following operations: : Remove the rope rotor as described in "Replacing the Starter Rope". FS 400, 450, 480) : Remove screw from the outer spring loop. : Remove parts of old spring. : Lubricate the new spring with a few drops of non-resinous oil (Special Accessories). FS 300, FS 350, FS 400, FS 450, FS 480 English / USA Storing the Machine 8 271BA038 KN : Place spring with frame in position – check that outer spring loop ( 8) is correctly seated. : Use a suitable tool to push the spring into the housing. Apply tool through the openings (see arrows). The frame slips off in this process. If the spring pops out and uncoils during installation: Refit it in the spring housing in the counterclockwise direction – start outside and work inward. : Fit the screw. : Install the rope rotor as described in "Replacing the Starter Rope". : Tension the rewind spring. : Fit the fan housing. FS 300, 350 9 9 271BA039 KN : Take out the screws (9). : Remove the spring housing and parts of old spring. : Lubricate the new spring spring in the new spring housing with a few drops of non-resinous oil (Special Accessories) . : Fit new spring with spring housing – bottom plate must face up. If the spring pops out and uncoils during installation: Refit it in the spring housing in the clockwise direction – start outside and work inward. : Fit the screws. : Install the rope rotor as described in "Replacing the Starter Rope" . : Tension the rewind spring. : Fit the fan housing. For periods of about 3 months or longer : Drain and clean the fuel tank in a well venti...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: