Оценок - 2, средний балл: 5 ( )

Производитель: Land Pride Размер: 8.75 mb Название файла: Язык инструкции:

Tighten cap screws (#9) to the correct torque. 3. Attach spike scrapers (#5) to scraper hanger (#1) with 3/8"-16 x 1 1/4" GR5 round head square neck bolts (#10) and hex flange lock nuts (#12). Draw nuts up snug, do not tighten until after completing adjustments in Section 3. NOTE: Do not tighten bolts (#8 & #10) until after adjustments have been made. See “Mud Scraper Adjustment (Optional)” on page 14 for instructions. 4. Attach scraper hanger (#10) to chain guard mounting bracket (#3) with two 3/8"-16 x 1 1/4" GR5 hex head cap screws (#8), 3/8" flat washers (#13), and 3/8" lock washers (#14). Secure scraper in place with hex nuts (#11). Draw nuts up snug, do not tighten until after adjustments have been made in Section 3. 5. Attach opposite end of scraper hanger to scraper mount (#4) with two 3/8"-16 x 1 1/4" GR5 hex head cap screws (#8), 3/8" flat washers (#13), 3/8" lock washers (#4), and hex nuts (#11). Draw nuts up snug, do not tighten until after completing adjustments in Section 3. Rear Mud Scraper Installation to Spike Roller Figure 1-4 30844 Table of Contents Section 2: Operating Instructions Operating Checklist Hazard control and accident prevention are dependent upon the awareness, concern, prudence, and proper training involved in the operation, transport, storage, and maintenance of the seeder. Therefore, it is absolutely essential that no one operates the All Purpose Seeder without first having read, fully understood, and become totally familiar with the Operator’s Manual. Make sure the operator has paid particular attention to: • Important Safety Information, Pages 1 to 5 • Section 1: Assembly & Set-up, page 7 • Section 2: Operating Instructions, page 11 • Section 3: Adjustments, page 14 • Section 5: Maintenance & Lubrication, page 30 The following information should be known and inspections made before operating your seeder. Check Reference Read and follow all “Safety Rules” carefully. Important Safety Information Read and follow “Tractor Hook-up” instructions below. Section 2 page 11 Read and understand “Operating and Adjustment Instructions” in this manual Operator’s Manual Lubricate seeder as needed. Refer to “Lubrication” Section 4 page 31 Check seeder initially and periodically for loose bolts & pins, “Torque Values Chart”. Section 8 page 36 Make sure all guards and shields are in place. Operator’s Manual Check initially and periodically for loose bolts, pins, and chains. Operator’ Manual Inspect seed cups and seed tubes for foreign matter. Section 3 page 18 Set speed change sprocket for drive type desired. Section 3 16 Set seed rate. See “Seed Rate Charts”. Section 3 pages 20 to 23 Tractor Hook-up ! DANGER Tractor hook-up to equipment is dangerous and can result in serious injury or death. Do not allow anyone to stand between the seeder and tractor during hook-up operations. Do not operate hydraulic 3-point lift controls while someone is directly behind the tractor or near the seeder. 1. Slowly back tractor up to the All Purpose Seeder while using the tractor’s 3-point hydraulic control to align the tractor’s lower hitch link holes with the seeder’s clevis lug holes. 2. Engage tractor park brake, shut tractor engine off, and remove key before dismounting from tractor. 3. Attach tractor’s 3-Point lower links to the seeder’s lower hitch clevises using 7/8" diameter hitch pins. Secure hitch pins with linch pins. 4. Attach tractor’s top center link to the seeder’s top hitch using a 3/4" diameter hitch pin. Secure hitch pin with a linch pin. 5. Ensure that the lower hitch arms are blocked to prevent excessive side movement. 6. Return to tractor and slowly operate controls up and down to make sure seeder clears tractor tires, frame, and drawbar. Move or remove drawbar if it interferes. 7. Manually adjust one of the tractor’s lower lift arms up or down to level the seeder from left to right. 8. With the seeder resting on level ground, manually adjust tractor’s top link until the seeder is level from front to rear. Transporting ! CAUTION When traveling on public roads whether at night or during the day, use accessory lights, and devices for adequate warning to operators of other vehicles. Comply with all federal, state, and local laws. 1. This seeder can be transported with a full box of seed, however; it is best not to do this unless necessary because the increased weight does increase the chances for problems on the road. 2. Select a safe ground travel speed when transporting from one area to another. Do not exceed 20 miles per hour travel speed. When traveling on roadways, transport in such a way that faster moving vehicles may pass you safely. 3. Reduce tractor ground speed when turning. Leave enough clearance so the seeder does not contact obstacles such as buildings, trees, or fences. 4. Shift tractor to a lower gear when traveling over rough or hilly terrain. Filling the Seed Box ! CAUTION Always lower the All Purpose Seeder to the ground before filling and checking seed level in the se...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: