Войти:
Оценок - 1, средний балл: 3 ( )

Инструкция по эксплуатации McCulloch, модель Cabrio 433B

Производитель: McCulloch
Размер: 295.19 kb
Название файла:
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


INSTALLATION OF THE TRIMMER HEAD SlotShieldBracket 3.Secureshieldtobracketwithbolt. Bolt CONFIGURING YOUR UNIT You can configure your unit using a cutting head for grass and light weeds, or a weed blade for cutting grass, weeds, and brush up to 1 cm in diameter. To assemble your unit, go to the section for the desired configuration and follow the instructions. NOTE: If your unit has a plastic cover over the threads on the threaded shaft, remove the covering to expose the threads. Before installing the trimmer head, make sure the dust cup and retaining washer are positioned on the gearbox. DustcupGearboxherAlignedholesShieldRetaining wasNOTE: Make sure all parts are properly installed as shown in the illustration before installing the trimmer head. 1. Align hole in the dust cup with the hole in the side of the gearbox by rotating the dust cup. 2. Insert a small screwdriver into aligned holes. This will keep the shaft from turning while tightening trimmer head. 3. While holding the screwdriver in position, thread trimmer head onto the shaft in the direction shown on the decal (counterclockwise). Tighten until secure. NOTE: The retaining washer must be positioned with the raised section facing toward the gearbox. 7 ASSEMBLY INFORMATION - --WEED BLADE WEED BLADE NOTE: Remove the trimmer head before installing the weed blade. To remove the trimmer head, align hole in the dust cup with the hole in the side of the gearbox by rotating the dust cup. Insert a small screwdriver into aligned holes. This will keep the shaft from turning while loosening the trimmer head. Remove the trimmer head by turning clockwise. Remove the screwdriver. See INSTALLATION OF THE CUTTING HEAD for illustrations. Be sure to store all parts and instructions for future use. Never use the trimmer head with the metal blade installed. INSTALLATION OF THE METAL BLADE WARNING: Wear protective gloves when handling or performing maintenance on the blade to avoid injury. The blade is sharp and can cut you even when it is not moving. WARNING: Do not use any blades, or fastening hardware other than the washers and nuts shown in the following illustrations. These parts must be provided by McCulloch and installed as shown below. Failure to use proper parts can cause the blade to fly off and seriously hurt you or others. NOTE: The dust cup is located on the gearbox shaft and not in the parts bag. All other fasteners mentioned in the following assembly steps are in the parts bag. 1. Install the blade and the retaining washer over the threaded shaft. 2. Make sure the raised part of the retaining washer is facing the gearbox and the raised area fits into the hole in the center of the blade. 3. Slide the blade and retaining washer onto the shaft of the gearbox. 4. Place the cupped washer onto the shaft. Make sure the cupped side of the washer is toward the blade. 5. Install the blade nut by threading onto the shaft counterclockwise. ShieldBladeRetainingwasherAlignedholesCuppedwasherThreadedshaftDustcupGearbox Nut Wrench NOTE: Make sure all parts are in place as illustrated, and the blade is sandwiched between the dust cup and the retaining washer. There should be no space between the blade and the dust cup or the retaining washer. 6. Align hole in dust cup with hole in side of gearbox by rotating the blade. 7. Insert a small screwdriver into aligned holes. This will keep the shaft from turning while tightening the blade nut. 8. Tighten blade nut firmly with a wrench (provided) while holding screwdriver in position. 9. Remove the screwdriver. 10. Turn blade by hand. If the blade binds against the shield, or appears to be uneven, the blade is not centered, and you must reinstall. NOTE: To remove blade, insert screwdriver into aligned holes. Unthread the nut and remove parts. Be sure to store parts and instructions for future use. ATTACHING THE TRANSPORT GUARD NOTE: The transport guard must always be attached to the blade when the machine is being transported or in storage. 1. Remove ends of wire retainer from the clips on the transport guard. 2. Lift wire retainer and position blade in transport guard. 3. Place wire retainer over blade and insert both ends of wire retainer back into clips. Wire retainerguarTransport d Clip 8 OPERATIONOPERATION WARNING: Be sure to read the fuel information in the safety rules before you begin. If you do not understand the safety rules, do not attempt to fuel your unit. Contact an authorized service dealer. FUELING ENGINE WARNING: Remove fuel cap slowly when refueling. This engine is certified to operate on unleaded petrol. Before operation, petrol must be mixed withagoodquality 2- --cycleair- --cooledengineoil designed to be mixed at a ratio of 40:1. A 40:1 ratio is obtained by mixing 5 liters of unleaded petrol with 0,125 liter of oil. DO NOT USE automotive oil or marine oil. These oils will cause engine damage. When mixing fuel, follow instructions printed on oil container. Once oil is added to petrol, shake container momenta...

Эта инструкция также подходит к моделям:
Садовые инструменты - Cabrio 115154526 (295.19 kb)
Садовые инструменты - Cabrio 952715746 (295.19 kb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории