Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
Reassemble the lower cap to the handlebar bracket in the reverse order of disassembly. 3. Locate the handle in the best position for operator comfort. 4. Firmly tighten both lower cap retaining screws. 5. Secure the cable to the outer pipe with the 2 bands as the illustration shows. The 2 bands are in the tool bag. Outer tube Lower capretaining screws Handlebar Ignition switch Throttle trigger Hanger Mounting the brushcutter handlebar Handle positioninglabel Bands Assembly (continued) Cutting Attachment Shield - C unit WARNING! NEVER use this machine with- out sub-shield when using a trimmer head. TX unit CAUTION! Make sure the sub-shield is completely hooked at the hook receiver. Sub-Shield (when trimmer head is in use) Attach the shield extension to the cut-1. ting attachment shield. Sub-shield Hook Hook Receiver Cutting Attachment Shield Attach the sub-shield to the cutting attachment shield for TX units when using a trimmer head Outer Tube Socket-Head Cap Screws Clamp Screw RetainingNut Mounting Plate Shim Shim Bracket Cutting AttachmentShield w/subshield Line Cutter CAUTION! Make sure the clamp screw and retaining nut are securely tightened before tightening the four socket- head cap screws. Insert the cutting attachment shield 1. between the outer tube and the cutting attachment mounting plate. WARNING! NEVER operate the unit with- out the cutting attachment shield installed and tightly secured! NOTE: It may be necessary to loosen the retain- ing nut and clamp screw to adjust cutting attachment shield mounting plate. Fit the two shims and the bracket over2. the outer tube and loosely install the four socket-head screws. Tighten the four socket-head cap 3. screws to secure the cutting attach- ment shield. Assembly (continued) Adjust throttle lever free play The throttle lever free play should be approximately 4 - 6 mm (3/16” - 1/4”). Make sure that the throttle lever operates smoothly without binding. If it becomes necessary to adjust the lever free play, follow the procedures and illustrations that follow. 1. Loosen the air cleaner cover knob(s) and remove the air cleaner cover. 2. Loosen the lock nut on the cable adjuster. Turn the cable adjuster in or out as required to obtain proper free play 4 - 6 mm. 3. Tighten the locknut. 4. Reinstall the air cleaner cover. Install trimmer head NOTE: This unit is shipped with Holder A, the blade retainer, Holder B, shaft bolt, and bolt guard installed. The shaft bolt is a LEFT-HAND thread. Remove it by turning CLOCKWISE! 1. Position the gearcase with the output shaft facing up and remove both holders. 2. Position Holder A as shown and slide it onto the gearcase shaft. 3. Install Holder B on the gearcase shaft. The machined boss on Holder A must engage with the recess on Holder B. 4. Rotate the gearshaft and holders until the hole in Holder A aligns with the matching hole in the gearcase flange, and then lock the holder to the gearcase by inserting the long end of the hex wrench through both holes. Throttle Lever Free Play 4-6 mm (3/16”-1/4”) Throttle Free Play Remove air cleaner cover Lock Nut Cable Adjuster Adjust as required for 4-6 mm free play Shaft Bolt Bolt Guard (not used) (not used) Holder AHolder B Hex Wrench Gearcase Shaft Lock the holder to the gearcase by inserting the long end of the hex wrench through both holes Using a counter-clockwise rotation 5. and hand pressure alone, thread and securely tighten the trimmer head into the gearcase shaft. 6. Remove the hex wrench from the gearcase and holders. Hex Wrench Hand-tightentrimmer head Thread and securely tighten the trimmer head into the gearcase shaft using hand-pressure The unit should now be completely assembled and ready for use with a trimmer head. Assembly (continued) In...
Эта инструкция также подходит к моделям:Садовые инструменты - 89303 (1.71 mb)
Садовые инструменты - 89303 (1.71 mb)
Садовые инструменты - 89303 (1.71 mb)
Садовые инструменты - 89303 (1.71 mb)